Other Network Architecture Subjects

Hi,One of my engineers had to break a password on a 2600 Router, so he accessed the ROM mode and instead of entering the value 0x2142, he entered 0x2412I am not quite sure of the value that he entered. All I know for sure that he entered an incorrect...

I have a new cisco 2600 router. It is used to segment beetween 2 internal lan nets - 10.10.0.0 & 10.80.0.0.I have the interfaces set with correcct IP. THey are both up. From the router I can ping all stations on either network fine.I can not ping fro...

Hi, My core router is Cisco 7500 series to which two distribution routers of 3600 series are connected. All of my customers are having Serial connections to 3600 routers. I want to limit their bandwidth without showing any degradation in performance...

what is the maximum speed that a cisco route can provide for x.25

Does anyone know how I can add a 2651 Router to my ConfigMaker network? Is there a plug in for it or can I simulate one somehow? Trying to use the 2621 but it does not support the 2 WAN WIC Slot Network Module that I am using on my 2651. Any help ...

Hi,I have a configuration question. I want to enable some snmp traps, but the Tech Note is not quite clear about this.I have a 3640 gateway with 12.2(8)T IOS (IP PLUS)I want to enable ISDN,DSP,VOICE and SNMP traps.Do I need config 1:snmp-server host ...

After upgrading flash memory and IOS on a 4700 M router, the router didn't load the new IOS. It is tring to load the old one which was deleted at the time of upgrade. Now I can only boot with bootflash. Please let me know how to set the correct pat...

I limit to 10 Ko the available bandwith for a host wich Ip adresse is 212.X.X.X , so the maximum bandwith for this host is 10 Ko ; when I try to download a file using ftp from this host ( download.com for example), the maximum speed of the transfert ...

HiWe would like to load share over the three different ISPs and NAT outgoing traffic on the basis of what interface the packets are routed through. This is a our config to show you how we tried to solve this.interface FastEthernet0/0 description insi...

Greetings. I have a lab that now requires a routed interface. The setup works like this. A router with a class A address and 24 bit mask (ex. 21.6.225.254/24) has an attached Catalyst 4006 with a L3 card. All lab nodes were configured on the same net...

I have implemented about 4 different 1720 routers. Problem is, they each need re-booted about every other day. This obviously shouldn't be happening, but it is. Is there a limit on the amout of NAT translations? The reason I ask is, when the LAN ...

I have a Cisco 806 router, it seems to take a while to resolve ARP's.When I initially ping a new device a may get a single ping time-out. If I look at the debug info on the Router I notice that I get an 'Encapsulation Failed' error for the first pin...

Hello everybody,Does anyone know a case/platform/IOS release, where the P-bit is not set for an external type-7 LSA generated on the router?This Cisco router is connected to a Juniper backbone (area 0) router which doesn't see P-bit set on type-7 LSA...

Due to HSRP running on my two 65xx switchs that are trunked together, I now have a whole slough of feasible successor routes that appear in my routing table. Having them in the eigrp topology table is no big deal, but it is really ugly in the routin...

I got an 5509-rsm 12.0(7)T with tokenring grouped through trbrf. It only produces 5% icmp redirects of what it should. bugtraq don't show a bug. Any idea ?