Other Network Architecture Subjects

Has anyone here used CiscoWorks 2000 to monitor the 4908s? I assume they can put out the requisite SNMP and RMON data, but are they fully integrated? For example can you look at them in Cisco View? We're looking at them as potential distro-layer s...

i searce for a describing for the command "debug tunnel". I got the output:Feb 21 17:24:58.800: Tunnel3: GRE/IP encapsulated 2.32.192.81->2.32.128.81 (linktype=7, len=438)Feb 21 17:24:58.976: Tunnel3: GRE/IP to decaps 2.32.128.81->2.32.192.81 (len=64...

Hi,I need to upgrade the IOS on 2900 switches but when I tried this on one switch, there wasnt space in flash I think so this failed. This procedure seems to be different to the routers. I dont quite understand where the IOS is stored and what I need...

Hi all,I am presenting the benefit of vlan to my customer and I need some numbers/white paper that might help to convince him in implementing vlan. I could not find the recommend no. of users/vlan or the no. of workstations that will degrade a networ...

Any comparisons on these two platforms? I'm building a small stack of 4 48-port switches and the price point/port density/gig options look similar. Any additional features in either that are worthwhile? It appears from the tech docs that the 3500 ...

I have 2 X 2504 Routers. With the first I can use the Control+Break sequence to break into ROMMON mode. However, with the second router using the same laptop and software I cannot break into ROMMON (therefore PC & Software is OK).In addition, I do no...

Is there a command under sh ip ospf that tells you where the last LSU was received from and how long ago. I swear I was using such a command a couple of weeks ago but cannot for the life of me remember what is was or if I dreamt it. The kit is a Cisc...

I have a T1-WAN offsite connected via a 2500 router to my main router 2611 home. I also have a PIX for Internet access on the home network. When comming thru the 2500 offsite I can't see the PIX. I can't even ping the PIX even from inside the 2500...

hello ,is it possible to increase the size of the files log in ciscoworks2000 such as " syslog ", because when I consult the ' log file status ', I find files log which largely exceeds the size to allocate by ciscoworks which is by default 3000 knowi...

Guys and Gals,Im looking into seeing if such a bit of software exists, but...is there an automated backup and compare piece of software for routers and switches (in fact any device which uses the TFTP protocol to transfer data (we have HP switches as...

I have just setup the company network switches for Remote managment. I monitor the bandwidth usage but would like to know export or publish the results, is there anyway to do this?Also if anyone else has an useful tips please feel free to leave them ...

I have only just got into our Catalyst 4000 after being here a few months. There is of course no documentation or anything. I logged in and printed a sh config and sh interface. Then proceeded to nose around and have a look.I noticed that one of the ...

I am currently using Route maps and prepend statements, but is there a way that I can truly load balance with BGP? How do the ISP's do it?Thanks in advance,JpoulosCCNP, MCSE

Hi,I read that 3600 is usually used for let's say larger branch office do access the central office via 6000 concentrator for example, but my question is: is it possible to make the 3600 act as a DSL concentrator, meaning is there way to accept sever...

I have to setup 32 Vlan, which will represent 32 seperate offices. I wish to allow each of the VLANs to access the internet and VLAN 1, but not to access the other client VLANs.Does any know if this is possible?Thanks in Advance