Is there a way that I can use QOS to only allow 100KB of http traffic for a certain Vlan ?
Is there a way that I can use QOS to only allow 100KB of http traffic for a certain Vlan ?
Hi,I saw the IP SNAT Conn Proc is holding the memory too much.Is there any bug for ip sant processor?My IOS version is C2800NM-ADVSECURITYK9-M), Version 12.4(5). 2821 is the router.Is the bug CSCsd66869 problem for my ip snat.But when checked with sh...
Sir,I want to configure intervlan routing(iwant to create 2-3 vlans and then connect 4 PC on this card ) on HWIC-4ESW . Does this card support ?regds,aman
Hi,I need some info about jumbo frames support on Cat2950 and 3550I've seen on CCO that 2950 support babygiant of 1530bytes and 3550 2000bytes...are this info still valid or in latest IOS they are enhanced ???Only Cat6500 support 9000 bytes jumbo ?Sa...
I am looking for a configuration guide / example that shows how to connect a Server with multiple NIC's to 2 different switches for failover. The servers could be Window's or Unix based. Thank you.
Hi,when show logging, there are few lines display destroy peer message. what's the meaning and how to solve it?========================================router#sh logging.Sep 12 12:13:31: destroy peer: 10.22.2.1.Sep 12 12:13:31: destroy peer: 10.22.2.3...
Hi all, if im seeting up a crypto map between 2 routers or pix's on a WES (lan extension circuit) have the ethernet interfaces got to be on the same ip subnet between them ? does the crypto map use the ip of the physical interface or does it have its...
udld basic questions1.what kind of hello packets UDLD is using? multicast?2.only aggressive mode send hello packet? non-aggessive will detect link problem by real traffic?Thanks
Hello,Just a question about HSRP best practices:I have two routers running HSRP on different IP segments using secondary IP addresses, with the following configuration:ROUTER 1:interface FastEthernet0/0 ip address 172.16.1.2 255.255.255.0 secondary ...
Imagine I have a production network running EIGRP, total of 5 routers. (2 routers in the data center, 1 router each branch office). I would like to setup the main office as "Area 0" and the respective branch offices I would setup as "Area subnet#_bra...
Can i do rate limiting for port 80 traffic on my 3550. If so can u please help me on the config. I want to rate limit on a single port
I need to do policy based routing based on the incoming IP address. All the addresses are coming in through a VPN concentrator and will be directed to one IP address on the concentrators policy, the concentrator will then pass the traffic to a switch...
I have a 3745 router recently returned from site. Upon boot, following error appears immediately: -"519: %PS-3-MULTFAIL: There is more than one failure with the Power System 2; please resolve problems immediately"Any help much appreciated!
Ok I have something wrong going on.I have 2 core layer 3 switches in HSRPVlan 10 172.18.10.0/24Vlan 20 172.18.20.0/24Core1 int vlan 10172.18.10.2standby ip 172.18.10.1int vlan 20172.18.20.2standby ip 172.18.20.1Core 2int vlan 10172.18.10.3standby 172...
If I have a (4) swtich stack, can I mix the images on the switches. ie: Can I have (2) 3750's running Enhanced and (2) running Standard? I'm guessing I can't, but would like to get confirmation one way or the other.Thanks
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |