Resolved! Does ASA Fail close upon failure?
Does the ASA firewall fail closed if the firewall filtering function is nonfunctional? I am trying to look for some Cisco docs about this but can't find it.
Does the ASA firewall fail closed if the firewall filtering function is nonfunctional? I am trying to look for some Cisco docs about this but can't find it.
I have ACL name-1 Over than 6000 lineWhen add this ACL cpu increase Cisco suggest ACL max 1000 lineHow add ACL name 2 and Related To ACL Name 1And How add ACL name 3 and related to ACL name 1Define 6 ACL Each ACl have 1000 lineHo Can Do this ?????Th...
See attachment of topology lab.So I have configured the 2 ASA for HA/failover. Now because I have redundant links from both ASAs to both csr1000 routers, I am looking for guidance on best technologies/design to use. Can I configure the g2 and 3 inter...
4G LTE Restart Authentication for testing I have a successful 4G connection setup. Is there a way to get the connection to restart and have authentication resent over the link. Currently I have tried shutting down the interface and bringing it back...
Hello For some reason, I am not able to ping PCs in either side of LANs. I am able to ping routers and PCs from router, but not from PC to PC. My network is very simple with two sites in different cities, connected with L3 MPLS. The Cisco Routers are...
Hi all,when i issued by sh arp on cat4507, some of the arp entry showed me it's mac address 0000.0000.0000.actually, these hosts not turn on. but i can ping these address. that is, someone response to me with the ping.here is the output on cat4507.Ca...
Hi all, I’ve been reading up and SPAN and the use of aggregator taps and full duplex taps. I feel i have a better understanding of each, but i still have a question that cannot seem find the answer to, hopefully somebody will know the answer to this...
Hi,Can any kind soul help me with my issues I've been facing for almost a week? I'm trying to do static destination NAT with the followings:192.168.1.1 (Source) -> 10.2.2.2 (Destination)Translated Address:192.168.1.1 (Source) -> 10.9.9.9 (Destination...
Hi,Can anyone assist me in finding the power consumption of WS-C3750X-24T-L, WS-C3750X-48T-L, WS-C3560X-48T-L and WS-C3560X-24T-L switches? Thanks in advanced.
I had to move NPS server to new network ( just IP change ) and after move NPS server stopped responding. There is nothing blocked on firewall, Cisco switches can see NPS server as UP but there is no traffic leaving the switch: RADIUS: id 2, priori...
Hi AllOne of VM switch’s management IP address is not responding and not able to do SSH But switch is up and runningChecked management Interface 0 also up,can you please suggest Switch model 1000v
Hello, im looking IOS for 2960S in version 15.2(05)E.in official repository there is only 15.2(2)E9 (in release note is mention even version 15.2(2)E10 and again its not available to download) :/in documentation and review is mention newer version th...
We had a Sup 2T throw a parity error, TAC RMA'd a replacement SUP2T. I ensured that the same IOS version was on the replacement. Inserted the card and in Show Mod it shows pass and ok however when I look at the show redundancy I am seeing the replace...
Hello I have Cisco VIC 1387 Dual Port 40Gb and HP dl380 gen 10 server . Can i use Cisco VIC 1387 with HP DL 380 server ? Is there any possibility and how can we handle the situation? Can you please share with me your recommendation to work this coup...
I tried to upgrade CPLD version 15010638 to 15010738 -in ISR 4451. Up-gradation status was quite normal and after re-load its showing old version only.. Before the CPLD upgrade Slot CPLD Version Firmware Version --------- -----------...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-20-2024 07:45 AM | ||
02-15-2024 09:08 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM |