Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Virtual Assistant - Discover support content and options for your gear Support page index - Contains...
Forum Posts
Resolved! RV routers CLI
Hello, Do RV routers, for example, the RV325 supports CLI through the console port and/or SSH?I'm thinking of using an RV325 router in a small network. Please check the picture below. What do you think of using an RV router for such network?
Resolved! Change Interface configuration
Hello, I do not have any experience with Cisco R&S and I have to change the following interface configuration to be 192.168.20.xxx instance of 192.168.5.xxxThanks in Advance. interface Vlan1 ip address 192.168.5.241 255.255.255.0 secondary ip ...
Resolved! Assist with Nat
Hello, I have Sophos XG-210 Firewall act as a gateway for the LAN and it's connected with Cisco router c888-k9I'm trying to Create IP Nat on the firewall but it seems something should be done on the router first because when I create the nat in the ...
I just posted this as a response to another thread but thought it might get more attention as a new discussion. Here's the discussion I responded to previously: https://community.cisco.com/t5/small-business-routers/rv34x-rv340-fatal-static-ip-wan-set...
Looks like the RV042G needs another firmware updates as the units we have in the field are now not passing PCI DSS Scans. Dealing with the compliance scanning companies, they are telling me that the firmware is the way to fix this. Here are the err...
We have an RV345 running 1.0.03.15 that I'm not having any success getting L2TP/IPsec VPN setup on. I have setup SSL VPN and can connect with AnyConnect but we would prefer to use the built-in Windows (7 and 10) VPN functionality. It seemed the PDF s...
I have an RV320 connected to a cable modem on the WAN port. every once in a while, less than a day but more than a few hours, the WAN port stops sending traffic. I tried Static and DHCP (im supposed to use DHCP but for testing I used static as well) ...
I have 4 RV345 running 1.0.03.16 FW. I have tried almost all the settings on in the VPN settings on the router but it is not connecting. I have raised a ticket with Cisco engineer but they suggest one thing a day(annoying when you have already tried ...
I have a new RV345 which I updated to 1.0.03.16 right after initial setup. It is replacing an RV320. I have a site-to-site VPN that was working perfectly between the 2 RV320s (one here, one remote). I can only get the VPN tunnel to work if I speci...
SNMP Seems to be broken after updating the Firmware to 1.0.02.16 from 10.0.01.20Before the WAN Bytes in and out MIBs where:WAN 1 1.3.6.1.2.1.31.1.1.1.6.51.3.6.1.2.1.31.1.1.1.10.5WAN21.3.6.1.2.1.31.1.1.1.6.61.3.6.1.2.1.31.1.1.1.10.6These no longer see...
Resolved! RV340 Binding Table
Hello, I'm trying to bind a specific IP to WAN2 for my mail server (SMTP services), but cannot set a single IP in the Source IP field. Only 192.168.1.0/24 is allowed as Source IP. My old RV042 works fine with this specific ip bind to WAN2. Any ...
Hi, We are looking at using this router for a fibre connection where the ISP requires a VLAN tag set. Does this router offer support for this connection type? Thanks, Nicholas.
I need some guidance on what product supports multiple subnets via an establish site-to-site connection with IPsec. I purchased a RV340 under the impression that it has this capability. After establishing the first tunnel, i tried to establish ...
We have a RV320 router that services a network of mobile users and a number of fixed workstations via ethernet. The RV320 has been working very well for almost two years. In the past week, several "lock ups" have occurred. After careful analysis, I w...