Routers - Small Business

Hi there,   here my situation: * My company-LAN use a RV320 * RV320 "gateway to gateway" VPN-tunnel to a third-party VPN: works fine (ping, ssh via company-LAN to the third-party machines) * RV320 "OpenVPN-Server" is up and running * RV320 "OpenVPN-A...

This router was updated some time ago. Since that time access to the gui has failed. I tried factory reset and I believe something occurred but not sure what as I still can't gain access. I tried from the wan side also, no joy.  What I think happened...

My customer has a RV320 at two locations with both dual WAN's (in Fallback mode) via different Service Providers (see the attached configuration). VPN between the two locations works fine but we have tried all possible settings to setup the Fallback ...

I have a Cisco RV320 that uses a public IP of x.x.x.181. Our ISP has also given us a block of 16 public IP's using a gateway of x.x.x.145 with usable IP's of x.x.x.146-159. I need to be able to pass these public IP's without NAT'ing to an internal se...

Is et up a new RV345 today and allw as good until a reboot.  Afterward I would just get Web Login Disabled.  All I dd during setup was ad some VLANs, changed all port to use the 192.168.75.1 vlan, enabled intervlan routing, created a VPN and set up s...

I just got a RV130 and setting up the VPNs   I followed the how-to from this link: https://community.cisco.com/t5/small-business-support-documents/configuration-of-an-ipsec-vpn-server-on-rv130-and-rv130w/ta-p/3172473 And the video from this link: htt...

The network setup is as follows:   One Cisco RV180 at site one plugs into a gigabit fiber modem on its wan port. This network operates on 192.168.0.x.   The other Cisco RV180 at site two also plugs into a gigabit fiber modem on it's wan port. This ne...

I am seeing a new log message that is repeating every 30 minutes.     charon: 11[KNL] creating roam job due to route change   I have no VPNs setup on this router.  There has not been any recent changes on my RV340 router.  I am running firmware versi...

Hey there, ( I apologize if this is the wrong group) We  have a Cisco 1941 on site that I don't have admin rights to.  The other night we were hit by lightning and the house went dark.  When the power came back the router came back on but there are n...

I am getting the following: yyyy-mm-dd, hh:mm:ss ALLOW UDP 216.218.206.114>4638 -> xxx.xxx.xxx.xxx:500 on eth1 where xxx.xxx.xxx.xxx is the IP of my router assigned by my ISP. Sometimes port 4500 is used.   These are both external IPs. Various extern...

  wan and internet redundencys Hi guys, while i am useing two wan connections and two internet connections (four separate connections ). Q 1 how i should configure wan redundancy with hsrp.  Q 2 should i use hsrp for internet redundancy als...

A new customer of ours has this RV 320 that has two ISP connected to it.  (The main ISP Comcast Business and then a fail over ISP Century Link.)  This router was setup by another company incorrectly  (Internet speed are extremely slow and it does not...

Hi guys, while i am useing two wan connections and two internet connections (four separate connections ). Q 1 how i should configure wan redundancy with hsrp.  Q 2 should i use hsrp for internet redundancy also.      Regards,  rammon.

The router continues to function, and can navigate on a web browser to the login page. But neither the previously set username / password combo, nor (using the reset button and powering on / off) the default username/password combo works. We're in a ...