Cisco’s security team has released an advisory for: RV340 Series Small Business routers (PSIRT Notice) Fix for bug CSCwc53007- RV34x GUI not accessible – The recommended fix is to upgrade to firmware version 1.0.03.29RV082, RV042, RV016 (PSIRT Noti...
Forum Posts
Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Virtual Assistant - Discover support content and options for your gearSupport page index - Contains a...
I have an existing SSL certificate which I'm trying to also use for my rv345 router (e.g. I don't want to use the rv345 to create the CSR as shown here (https://www.cisco.com/c/en/us/support/docs/smb/routers/cisco-rv-series-small-business-routers/smb...
I've noticed that the end-of-life is approaching for the RV325 dual WAN router. At: https://www.cisco.com/c/en/us/products/collateral/routers/small-business-rv-series-routers/eos-eol-notice-c51-743069.html in a document dated October 31, 2019, it say...
When using Client-to-Site VPN Tunnel Status with EASYVPN configured, I'm unable to see which specific user is connected. The IP address is displayed along with other information but that's not helpful for being able to tell which specific user is lo...
I have multiple RV340 and RV340W routers deployed with the latest firmware 1.0.03.17. It appears that if the IP address is a Static IP address (e.g. 192.168.xxx.xxx) then the Hostname does not display in the ARP table. Further, after specifically add...
Hi Team,I am highly frustrated, I purchased the RV042G for our remote office to enable them work from home and for the past 5days I have been trying to create a remote access VPN on this device but nothing seems to work except PPTP.My WAN interface...
Hi everyone, The ISP that provides my internet (rhymes with pie) uses a rather odd way of authenticating users on their circuits (they don't use PPPoE), when a modem requests a WAN DHCP address it has to provide username/password string within DHCP o...
Hi All, I need to subnet an IPV6 address from Comcast so that I can distribute it to my VLANs. In the past I've done DHCP-PD and been able to chop the prefix down from 64 bits to 60 so that I can subnet it and distribute it to my VLANs. This router w...
Hi all.I have a new RV260 router running on 1.0.00.16 system image.In short. First thing I need to do is connecting to a serial console of the device. I connected my device via the serial port on 115200,8, N,1. I think my settings are correct because...
I have an RV340W (firmware 1.0.03.17) and a USB730L. The combination works mostly fine, except that it freezes at random during periods of large transfers (sometimes "large" is defined as 10 megabytes in 5 seconds). There seems to be no rhyme or reas...
Resolved! No access to RV130W
Hi,I have a RV130W. It stopped working and I found it with a fast blinking POWER LED.Reboot did not helped. Pressing reset button also gives no result.Direct ethernet connection of PC is not helpful. Even the LED does not indicate connection and PC s...
The goal is to use the router to terminate two wan connections for two separate networks, use the router for ip blacklisting, terminate vpn site-sites, and pass the accepted traffic to the ASA for further processing. I tried the RV-340, but I could ...
Just bought a RV340 for a small company. I'm baffled by the Firewall->Port Forwarding config page. I've configured many routers over the years, and they all allow one to specify if port translation is needed. e.g. forward port 3390 on WAN side to ...
Resolved! RV340 - 802.3ad Support?
Hello, Documentation for RV340 does not mention support for link aggregation 802.3ad protocol.Does the RV340 support it? One goal is to aggregate for increased throughput, not port mirroring for packet capture/analysis.Any suggestion for this?
Hi, i am having differents IPs trying to access throw my vpn. I set a couple of rules to block this addresses but keep loging trying to access, and firewall logs are empty. This are the rules, deny All from those Ips And this is one log from this mor...
I have an RV320 which is also my DHCP server and has DNS set to "Use DNS Proxy". In the "DNS Status Table"I can see the names of my clients and their IP addresses. But I can't access any of these devices by name, only by IP address. I had assumed ...
