According to this, I should be able to utilize the cellular interface's GPS as an ntp refclock but the refclock command is missing completely.I'm running 17.09.07b IOS-XE on a Cisco 8200L with P-5GS6-GL. The cellular controller config is:controller C...
Forum Posts
Hi allI’m in a bit of a pickle and could really use some guidance. I’m a beginner in Cisco Packet Tracer and my assignment (final) requires me to design a fully wireless network that has three floors - Ground, first, and second each with a different ...
Hi everyoneI have a question about running multi-area OSPF.I have a pair of C8300s, using about 80 areas, is that safe? Each area only advertises about 5 subnets to Area 0.
I have a question regarding CDP behavior on Catalyst 8500 routers.I have two 8500 devices connected via a fiber link. After enabling CDP globally using the cdp run command on both routers, I ran the show cdp neighbors command — but no neighbors were ...
Hi, how to check the throughput on catalyst 8300 router? Is the output of the following command representing the overall licensed throughput of the router or only represent the throughput of VPN only? Can someone pls advise? thanks in advance! I onl...
Resolved! Cisco 1117-4P VDSL Bridge (IOS-XE 17)
Goodmorning, For multiple customers I have a Cisco 1117-4P where the ethernet0/2/0 interface is bridged with a VLAN interface so the custumer can connect their own router/firewall and let it handle the PPPoE session. In the past we used the Cisco 887...
Hello. I have a Cisco 829 ISR stuck booting to ROMMON-1. I do not have a Cisco account needed to download the images from cisco.com so we asked our contractor to provide the images. They sent us the two files below which to my understanding is the IO...
I have typed below command, normally it has to let me enter yes or no but in mobaxterm when i press enter it is jumping to next line R1#, skipping Reset ALL OSPF processes? [no]:anyone faced this? pls help. R1#clear ip ospf processReset ALL OSPF pr...
Resolved! GRE tunnel and ssh
This might be a dumb question but I just noticed something with a gre tunnelBrought up a new gre tunnel src 10.0.1.1 dst 10.0.1.2tunnels stable I can ping the dst address from the source on both sides. Why can’t I ssh to those addresses across the t...
Hi, Does C8300 Essential license support BGP VPN4 or Advantage is needed? Kind regards
65791: Mar 3 02:53:14.759: %BGP-3-NOTIFICATION: sent to neighbor 182.19.96.80 4/0 (hold time expired) 0 bytes 065792: Mar 3 02:53:14.760: %BGP-3-NOTIFICATION: sent to neighbor 182.19.96.17 4/0 (hold time expired) 0 bytes 065793: Mar 3 02:53:14.760: %...
Resolved! BGP/OSPF Reditribution
Hi Folks,Hope all are doing good.I need your support on one case where we are having eBGP between upstream ISP to my core router and inside my networks multiple routers are connected with my Core Routers and Running OSPF internally.Done redistributio...
We have a new router (ISR4321 XE) with NIM-2BRI-NT/TE for voice, and we are unable to configure the BRI NIM card. Cisco website recommends a minimum IOS level for this hardware was 16.6.1. We upgraded the router to 16.6.3 , and it's still not working...
I'm interested new devices of secure routers have the same policy for getting hsec license to do ipsec performance above than 250m?For example C8151-G2 has ipsec performance 1.5gbps and sdwan 900mbps but strange there is no information how can I get ...
