Hi, I'm trying to set up OSPF between 2 routers with subinterfaces. Unfortunately, OSPF doesn't come up with the subinterfaces. If I set up OSPF on the main interface, everything works fine. The connection is between different sites in the country. C...
Hi AllIs it possible to show logs matching a deny ACL rule?When you add the log keyword to the ACL what exactly does this show you? just hits or will it show you a log of the actual source IP etc?If the above cannot be achieved, would you need to use...
<p> </p><p>I am currently practicing the configuration of DHCP servers and routing in Cisco Packet Tracer in preparation for my exam.</p><p>My setup consists of two routers, each connected to two switches, with one DHCP server assigned for ever...
Hi All, Refer to the diagram Host-A can communicate Host-B and Host-C can communicate with Host-D but Host-A and Host-B can not communicate with Host-C and D. Where as every where route is available. NOTE: From R-3 and 4 I can reach Host-C and D Fr...
When entering the command "show control-plane host open-ports" on a router, with web services running and no current connections, the command output shows two entries for Port 80, and two entries for Port 443. Why two of each? Does this mean the rout...
Hi, a while ago i received 16 routers and they all didnt work: The solution But the router i used to try the solutions now isn't able to go thru with this solution when i boot the router it gives this output and stays in a loop of this:Initializing ...
I was just testing something and noticed an odd debug.I have three routers testing something, all just plain vanilla configs, and adding a static route to a loopback address and I'm able to ping and traceroute to it, and I thought it was just fine......
Hi All,I'm trying to balance our 4 Subnets over 2 ISP's using BGPMy situation: we have 4 Public v4 Subnets lets call them (not my real IP's)NET1: 200.0.1.0/24NET2: 200.0.2.0/24NET3: 200.0.3.0/24NET4: 200.0.4.0/24I want NET1 and NET2 to use ISP1I want...
Hi,I have a cisco 9200 switch which is not syncing to NTP server (Linux based). No firewall is in between switch and NTP server Switch is able to ping NTP server IPUsing management vlan, not an vrf Switch9200#sh ntp statusClock is unsynchronized, str...
Network Diagram briefPlease refer to the attachment or the following for the network diagram Please note it is a lab diagram for learning and testing purposes.-> There are 4 IOS XE Routers-> The interface links are represented in the following form...
The router is RV320, preparing to enable remote access. After setting up DDNS and external network access ports with the RV130 I used before, I could directly access it. However, this model prompts a 502 BAD GATEWAY error. Could someone please guid...
Hello all!I ran into an issue when assigning a channel group to an interface on my C9372PX core switches running EIGRP. I created a port channel on both cores and assigned the channel-group 45 to interface Ethernet1/45 with no issues. When attempti...
Hello I have the following configuration on a subinterface and I what to remove the RIP configuration from it. interface TenGigabitEthernetx/y/z.100 bandwidth 20000encapsulation dot1Q 1234vrf forwarding vrf-nameip address 1.1.1.1 255.255.255.252ip fl...
Our client recently purchased a Network Advantage license to upgrade an existing IE3300 switch from Network Essentials. They need this to enable EIGRP routing functionality. I ran through the license reservation upgrade procedures from the Cisco docu...
Hi, all,I have an RV325 (yes, I know it's old) and am having a problem.When I first got it I did a factory reset and updated the firmware to V1.5.1.13, which worked ok. I was able to sign on using cisco/cisco and start configuring it.When I tried to...
