Hi What is the throughput of the Cisco 2901 router. Can i have 1Gbps internet connection to this. Will this router support this speed as a Internet CE router ? rick
Forum Posts
i am setting up a Cisco isr 4431 when looking thru my config my username / password is in clear text . is it possible to mask this password? #username username password 0 mypassword
I have a Cisco 1841, coming from the 10.100.100.0 network, i would like to be natted for the 10.20.1.0 network as i was coming from the 10.20.1.1 interface and for the 10.50.1.0 network as i was coming from the 10.50.1.1 thank you
Catalyst 3750 series PoE-48 Cisco IOS Software, C3750 Software (C3750-IPBASEK9-M), Version 12.2(53)SE2, RELEASE SOFTWARE (fc3)ROM: Bootstrap program is C3750 boot loaderBOOTLDR: C3750 Boot Loader (C3750-HBOOT-M) Version 12.2(44)SE5, RELEASE SOFTWARE ...
Hello Experts, Background I have two HUBs (diff physically location with dual ISPs) and rest 6 are spokes(4 have dual ISP and 2 are with single isp). Is it necessary to have VRF on spoke with single ISP ? issue is: all 4 spoke (with DUal isps) ha...
Hi all,I have a Cisco Switch NEXUS 3048 with nx-os 6.0(2)U3(7) and licence LAN_ENTERPRISE. I want to know if the following if possible: I have a simple network for an experiement. I have a Router #1, which gives me the up-link to the rest of our n...
Hi,I want to adapt the Applet in this way, that IP addresses 10.124.132.1, 10.124.132.2 and 10.124.132.3 and 10.124.132.4 are excluded from the Action, for all other addresses in the range 10.124.132.0/22 the Applet Action must be triggered. My issue...
Dear all , I would like to know stupid question.I have the problem to integrate existing network and HA firewall. please see below diagram and let me know can i conbine two routed interfac to one virtual IP ? it is not mean vrrp. i mean i want to run...
Hi I have ISR 4451-x router running zone base firewall and NAT. Working setup ip route 0.0.0.0 0.0.0.0 x.54.23.254 interface GigabitEthernet0/0/0 description Internet ip address x.54.23.210 255.255.255.248 no ip redirects no ip unreachable...
After much time without success, I resolve to seek help with RSVP.I'm trying to setup a basic RSVP lab, as a basis for the next step, which is RSVP-TE/MPLS.Alas, something seems wrong. Here is the setup: The routers run IOS 15.4 (I also tried wi...
Hello, I am a networking student. I was prompted by this page when I clicked on "ask a question" so I apologize if this actually isn't the right place to ask this. My problem is pretty simple and I think the solution will be simple too, but for ...
Hi, i am using ISR4321/K9 router with 2 WAN and 1 LAN cards. Two ISPs are connected to WAN and the LAN side is connected to Firewall. ISP 1 is 50Mbps and ISP 2 is 80Mbps. after running Platform hardware throughput level to change to 100Mbps, i lost i...
Hi allI have a question! Can I connect back to back two modules VDSL HWIC without DSLAM? Thanks.
Resolved! IPv4 Supernetting
Hello, I'm trying to expand one of our subnets and wanted to get some input to check and see if I'm doing the calculation properly: The requirement is to create a /19 subnet (172.18.64.0/19) to use for wireless network; however, I'd like to use ...
I have a server that I need to move to another network whose IP address I can't change. For example, the server is on the 192.168.0.0/24 network with an IP of 192.168.0.100 and I need to move it to the 192.168.10.0/24 network. Each network has a gate...
