Hi all, we got Cisco 3750 and HP Switches GbE2c L2/L3 from Blade with trunk and LACP. Is working, but i see in the bandwith graph more traffic one an interface than the other one. ¿No load balacing? On Cisco 3750 interface interface Gig...
Forum Posts
Hi,I need to replace the fan on a Cisco 3725.Anyone know if the fan of some other equipment is compatible with my 3725?..Can you tell me which model of router has a fan with similar characteristics that may serve a 3725?.I leave some specs of my 3725...
1)Two hosts are attached to a switch with the default configuration. Which statement about the configuration is true? A. IP routing must be enabled to allow the two hosts to communicate. B. The two hosts are in the same broadcast domain. C. The sw...
Hi Community Team' I hope you are doing well. I am trying to configure PPPoE on Catalyst 3750G-24TS for users to authenticate with remote radius but I couldn't find the some of commands. Currently My switch SDM template is "Desktop routing". Please s...
Dear Support all, I would like to configure Multiple Outside NAT on Cisco IOS router with the following condition, Same Outside Global IP/Port, Same Outside Local IP but different Port number. Here is the output for this however I think there is li...
We have 13 sites and 1 data center (host site). Our topology will be point-to-multi-point. We will be using ASR 1001-X and ISR 4331 routers for the EVCs. Looking for configuration samples I can use as reference in configuring the bridge-domain, se...
Resolved! ASR1001 vs Catalyst 3850
I have two Ethernet hand-off Internet circuits from two different ISP at two different locations. There are three locations connected internally, and the bridge VLANs across all three locations. The two ASR ISP routers (running IP services) ...
Hello everyone, i have vdsl at home and i want to connect a new router 896VA. for germany and provider M-Net i dont know if it needs pppoE or pppoA.then it someone has the same topology, can we compare my configuration...because they tell me i need...
Resolved! HSRP FALL BACK ISSUE
Dear Team, I am running HSRP for my LAN.whenever my R4 is going down R5 came to active but if R4 came up again the fall back is not happening up to my R5 is going down. R4 : R4#sh run int fa0/0Building configuration... Current configuration :...
Hi,In this document, I am able to find the Routing Performance for all routeurs except ISR 4000 series. http://www.cisco.com/web/partners/downloads/765/tools/quickreference/routerperformance.pdf I would like to know what is the Router Switching Perfo...
Hi buddies, I've an issue with OSPF external routes and I cant understand why the routes cant be installed on the routing table. The topology of the network is like below: R1(10.1.1.2) -> (10.1.1.2)R2(10.1.2.2) -> (10.1.2.3)R3 So a OSPF routing proto...
I would like to ask some help to fix my configuration by using Multiple DHCP with internet access. Currently my configuration below is connected to multiple dhcp unfortunately unsuccessful Internet access. Current configuration : 1449 bytes ! versi...
Case 1: PC A sends a packet (8bytes padding, 20B TCP Header, 20B IP Header, 18B Ethernet Header) with 0 sequence number to PC B. PC B will send an ACK Message (ACK Number = 0) Right? Case 2:PC A sends a packet (Phantom Byte(1B), 7bytes padding, 20B T...
My understanding is If PC A sends a packet (ACK = 80, Sequence Number = 1450, Payload = 1460), PC B will send an ACK Message (ACK = 2910, Sequence Number = RANDOM). If I am misunderstanding, please let me know.
Hi Guys, I'm facing something interesting here. The situation is the following: I have MITEL IP phones in the whole building and some people that moves from desk to meeting rooms and back to desk (lots of meeting). If a person connects her laptop t...
