HiI have a Cisco 887VA router that I'm trying to connect to a VDSL2 service.I'm getting this error when the VDSL2 service is plugged in: %VDSL_DAEMON-4-TRAINMODE_NOT_SUPPORTED: ATM transport mode is not supported on VDSL2.Here is the controller detai...
Forum Posts
Hi All Can someone please help me with the difference between CON-SNT-SLASR1AK and CON-SNT-ASR1001X? Do I need both of these if we have a ASR1001X? Thanks Gordon
Hi guys, I am trying to learn vtp, so I am using GNS3 for the simulation with two switches. I have built simple connection between two switches, configured trunk and vtp server / client modes. I was curious about this question. What happens when I ha...
I'm having a strange issue I've never seen before with routing. Here is the scenario.... I began advertising a route from the UK across our IPVPN WAN which comes back to two sites in WI. The two WAN routers are in the same EIGRP domain and are NOT ...
Hi, I am having Cisco 2921 router with two ISP. I want to configure load balancing between these ISP's with "load balancing per packet", but my VPN packets should super seed the load balancing configuration and should go only through primary ISP....
Hello guys any good config example for MPLS VPN L3 act as primary connection while IPSec over the internet acts as a 2nd connection , routing protocol is OSPF thanks
Resolved! Reply Packet path selection by router
Hi, I have two VPN (DMVPN and IPsec VPN) connection between SITE A (HO) and SITE B with two different ISPs. The DMVPN is configured with Dynamic routing protocol as EIGRP and the second VPN is configured with static route AD value 171 (Higher then E...
Hello Scenario - I have two ISP's terminating on Cisco Firewalls (Active/Passive) - is it possible to run BGP between the two ISP's and the pair of Cisco Firewall (failover mode) - I am not how the iBGP will work between them as they both share the...
Resolved! VRF - Unreachable NH Issue
Hello, I'm practicing VRFs in GNS3, I have four routers: PE-1, PE-2, CustA-HQ and CustA-Remote. I'm unable to ping CustA-HQ from PE-2, but can ping the interface to which it connects on PE-1. When running debug ip packet detail on both CustA-HQ and...
Hi Experts,I wanted to know about L2VPN functionality with below scenarios., What will be the behaviour of PE1 and PE2 when CE1 is tagged/untagged with different VC type configured. Topology:CE1-------PE1-------LSP---------PE2------CE2 Scenario 1...
Hi everybody, I have a doubt about a SVI and a Loopback with the same IP range in the same router. Some days ago I tried to configure a SVI and a Loopback in the same router and the CLI answered me that it is no posible to have a SVI and a Loopback...
Hello Freinds what the below means , kindly decipher it , what is the reason behind that ? wic card location 0/2 is FXS *Mar 18 14:35:47.951: %MAINBOARD-1-UNKNOWN_WIC: wic card in location 0/2 has an unknown id 0x47*Mar 18 14:35:48.823: %ES...
Resolved! Configuring cisco ISR 4221
Hi Guys, I have ISR 4221 with 2 GE ports (Layer 3 ports) and 4 ES2 ports (Layer 2 ports). and i have 1 WAN and 1 Internet Link and 1 Inside(LAN) link. i wanted to enable both WAN and Internet connection for all LAN users. how can i make this to work....
Hello guys where can i find the activation-keys for the below permanent license on my router Technology Package License Information for Module:'c2900' ------------------------------------------------------------------------Technology Technolog...
We are asked to deploy IPv6 in dual stack in our network in order to enhance our IPv6 rank . As we are new with this technology can you guide us? Shall we Address all our internal network with public IPv6 addresses in order to enhance our rank ?...
