Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

Hi I have main HQ and 7 branches and these branches connected to HQ over MPLS . I want to apply backup soulution over internet . what is the best way to do that and i have one router in each branch face to the internet and MPLS . 

q1gznn111 by Level 1
  • 1195 Views
  • 6 replies
  • 0 Helpful votes

I have a nexus 3064pq (not X) and all the commands related to applying a mac address access list seem to be missing. I have it upgraded to 7.0(3)I4(6) and I can create a mac access list but all the commands related to applying it to a port or vlan se...

I have a dual-hub DMVPN setup running OSPF. The issue I am having that the default route that's being injected is preferred on the secondary hub instead of the primary. I've tried adjusting the metric on the default route, changing the admin distance...

davem1 by Level 1
  • 1702 Views
  • 6 replies
  • 0 Helpful votes

Hello, Currently I’m looking for networking monitoring system for a DC Network which have ~200 nodes in 6 different geographic locations. All equipment is CISCO but different IOS version (IOS-XE,IOS-XR,NX-OS, IOS) Primary thing would be to monitor th...

from88 by Level 4
  • 681 Views
  • 2 replies
  • 0 Helpful votes

I have a 2811 running as my frame cloud for a home lab. I'm looking to use a NM-4T 4-port serial module to connect 1841s via WIC-1T cards. My 2811 is complaing that the NM-4T is not supported with my version of IOS. Can anyone tell me what verison of...

hrvxla by Level 1
  • 860 Views
  • 2 replies
  • 0 Helpful votes

Hi,I'm wondering what would happen if you connect two switches together with two up-links where all 4 ports are configured as access ports with portfast enabled? No BPDU Guard.I know all ports should transition into forwarding state immediately and c...

hello, need your help.i have switch cisco WS-C2960L-16TS-LL, Cisco IOS Software, C2960L Software (C2960L-UNIVERSALK9-M), Version 15.2(5c)E, RELEASE SOFTWARE (fc1). i cannot run command "port-channel load-balance":cisco01(config)#port-channel ?auto LA...

Yame by Level 1
  • 941 Views
  • 1 replies
  • 0 Helpful votes

Hi all, I'm having an issue that i hope somebody can help me with.  We are running a DMVPN environment and I have a couple of spoke offices that run voip over their tunnel to each other.  The issue is that we swapped the ISP in spoke A but now the la...

Cory King by Level 1
  • 3564 Views
  • 7 replies
  • 0 Helpful votes

Hey Cisco Community: I have a simple question.  Can I NAT just my guest wireless network, whose VLAN gateway sits on my L3 switches (HSRP), onto a public IP and not have it translated again by my second NAT, which sits on the last hop out of my netwo...

network.jpg

Question for the collective- When configuring multiple NTP server entries on a network device, if you do NOT use the "prefer" argument, does the network device compare the NTP packets from all entries and dynamically determine the best one to use? I ...

R_Acuti by Level 1
  • 7690 Views
  • 6 replies
  • 0 Helpful votes

Resolved! Route-Maps Issue

hey Community Team'Recently I am observing an issue with route-maps. Two links from different service providers are terminated on Router 2911. Default route is set to ISP1 & all traffic is working normally. When I applied route-map to send some traff...