where to get answer of any error detected in logs of cisco switch & router
where to get answer of any error detected in logs of cisco switch & router
Hello Community,Just chasing some feedback on the setup that load balances traffic on the both WAN uplinks that are connected to 2 Starlink kits.I know its going to be ECMP using the equal cost but my question is what would be the best implementation...
Hi DMVPN Pros Maybe a DMVPN hero can help me out. I have a DMVPN setup with multiple spokes that are behind the same CGN (mobile 4G network). So there is a possibility that 2 CPEs may have the same public IP address after processing the CGN. Is this ...
I'm trying to debug and only view ICMP traffic between 2 specific host via ping, but there are so many messages, it's hard to troubleshoot. Is there a way to filter and see only the ICMP traffic between them? I've tried debug ip icmp and using acl(...
Hi, Need Help !!!! How i configure bandwidth limit on IP (not on port) in Cisco 3750 My configuration access-list 150 remark ****************test***********access-list 150 permit IP any xxx.xx.x.xxx 0.0.0.3access-list 150 permit IP xxx.xx.x.xxx 0.0...
how to check error occurred in cisco switch or router for last 1hrs
I have ACLs set up and they're working, besides the one set on leaf 2. I only want sales and marketing PCs to ping the sales and marketing server and finance and operations PCs to ping the finance and operations server. All other servers should be ab...
Hello, friends!I need your help because I am unable to understand on my own where the problem is.Long story: Subnet 188.241.240.0/24 was used via BYOIP with OVH (AS16276) in Germany even though it was still routed via my ASN 57403 from Romania where ...
I have ACLs set up and they're working, besides the one set on leaf 2. I only want sales and marketing PCs to ping the sales and marketing server and finance and operations PCs to ping the finance and operations server. All other servers should be ab...
I recently started studying for my CCNA and bought two routers and two switches off of eBay to start a lab. The guy I bought the routers from forgot to mention that the routers run a DC psu that I don’t know how to use. I wanted to just swap a AC psu...
Hi, I having some issues with my GRE tunnel. The traffic between sites are going through the GRE tunnel, so clients traffic is not affected. I have two issues that I have found. The first one is the duplicate ping replies. Whatever I ping, there is a...
I am testing FortiSwitches on our network, I have a 224e that I am trying to trunk directly to an ethernet port on my cisco 9300. I have trunked the port on my cisco port 36 interface GigabitEthernet1/0/36description Uplink to Fortiswitchport trunk a...
Hi all, I am trying to perform a password recovery on a Cisco ASR 1006, I can ctrl + break and set the register to 0x2142, i then power cycle it, but it keeps booting back into the 0x2102 register. is there anything different about this device?
See attached file. I need to be able to ping across the network,it isnt working. DHCP is working, assigned from the routers. I also include the routing tables. EDIT: i was able to get pings to orlando work by modifying the network. I still can't pi...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
06-14-2025 01:24 AM | ||
05-15-2025 07:28 AM | ||
05-13-2025 03:49 AM | ||
05-12-2025 03:28 PM | ||
05-09-2025 02:25 PM |
User | Count |
---|---|
9 | |
6 | |
2 | |
2 | |
2 |