I am using EBGP between PE and CE, and CE generate a default a route to PE. I am using "default-originate" on CE But PE received this route but not selected. Could anyone help check? Thanks I am using XRv platform to test this. Configuration on PE: ...
Hi All Can anyone tell me what the cisco AX Experience routers can do for me, what are the fundamentals on how they work? do they just use netflow and pfr/oer?, do they do any optimization / caching ? how are these policies configured etc cheers
Hi, I have a scenario where the routes on my core2 at site B are learned from all the 4 VLAN interfaces on Core1 at SiteA. Attached the NW diagram for your reference. O E1 10.0.0.0/16 [110/23] via 172.16.3.130, 5d03h, Vlan104 ...
Hi all Cisco Experts, Good day! i just need help on implementing redundancy and load balancing on our two (Frame relay/ISP) network from our branches. I want to now what are the devices capable of redundancy and load balancing and also its required ...
Hi there, We have ASA 5540 that must route two ISPs with different NATed addresses for each ISP. ISP selection is based on source IP addresses. I can use a router for the purpose of choosing outside. but I don't know why only one outgoing line is ac...
Hello, We're testing one feature of Cisco Catalyst 3k switches and there is a problem. QinQ feature works fine only for one tunneled C-VLAN, if there are more C-VLANs, nothing goes through the tunnel. Is it possible that there is a Cisco 3k problem?...
Hello all, Is anyone else having issues updating the software on an asa via the ASDM? I am using the wizard and login ok but the wizard fails and comes up with an error saying "Unable to upload wizard successfully" I have tried on multiple devices a...
Hello All, I have what I hope is an easy question. Device: ASA5512 IOS: 9.5(2) Goal: I would like to set up my ASA to use interface names that are not "outside" and "inside". Information: I know how to change the names of the interfaces, add NAT ...
can I insert HWIC-2FE when it is online? thanks,
I want to understand what is the use of NAT-T ? i have gone through many documents but still confusing me. we have a site to site vpns between two ASA firewalls , so i have disabled NAT-T on asa firewall but still both sites are communication each ...
Hi Guys, Hoping someone can help we have an satellite office connected back to us over 2 Metro Ethernet links 10Mb & 20Mb, for where we present internet transit. I have 4 cisco 2901s on each side of the links and tried using GLBP, to fully utilise ...
Hi Experts, I need some help from you to understand how the software queue would work in a situation where shaping with nested queuing is applied on sub interfaces. I understand that eacch Interface has a buffer that it uses to queue excessive packe...
Hi I have a Cisco switch and the utilization is going crazy, i have ensured that line con 0 does not have logging synchronous as it was identified to sometimes cause the high utilization (Cisco bug ID CSCed16920 or Cisco bug ID CSCdy01705). I have ad...
Hello Experts we discuss about BGP return traffic issue is comes actually i have 3 ISP links it is connceted on single router i have adverties only one ip public pool ex. 103.205.x.x/24 ISP 1 =20 mb ----active ISP 2 =4 mb ---- passive ISP 3 =4 mb ---...
I am in a new environment where I see few ASR 1002-x series routers. I wonder how I can make sure these are on which ESP license level. Is there any command I can run and verify? Thanks, Josh
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 12-05-2025 03:27 AM | ||
| 11-13-2025 04:57 PM | ||
| 11-09-2025 09:51 PM | ||
| 11-06-2025 06:09 PM |
| User | Count |
|---|---|
| 3 | |
| 3 | |
| 2 | |
| 2 | |
| 1 |
