Buy or Renew
Buy or Renew
Notice: The file download function is disabled. We apologize for the inconvenience.

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
Labels

Forum Posts

Start a conversation

Resolved! isis behaving strange

Hello Team, Below is ISIS database but output i can see the routes & neigbour UP, but it's not showing in routing table. What should be my next step. I am able to see all routes of R1 in R2 R1#show isis database R2.00-00 detail Tag area_0041: IS-IS L...

yualme by • Level 1
  • 3246 Views
  • 8 replies
  • 0 Helpful votes

port mismatching

Hi, I connected Cisco 2960 and HP 1910 Switches together with default configs but ports didnt became UP.Then I assinged VLAN 200 on Cisco sites and ports was UP for a while and then a few hours later ports became DOWN again.whenever I do "shutdown a...

selbay061 by • Level 1
  • 583 Views
  • 4 replies
  • 0 Helpful votes

DHCP server in another VRF

hello, I have my DHCP server that is in a Vlan of my VRF A and another Vlan in another VRF that contains clients When clients and server are in the same VRF control IP HELPER-ADDRESS x.x.x.x(ipofmyserverDHPC) is correctly Control IP HELPER-ADDRESS V...

Port-security is not sending snmp messages on 2960x with ip source guard port-sec enabled

We have 2960x switch (WS-C2960X-48LPS-L  15.0(2)EX4   C2960X-UNIVERSALK9-M) and have configured on access ports port-security, ip source guard (IPSG) and also DAI and DHCP snooping enabled globaly on switch. The problem is that when we configure the ...

Resolved! Doesn't work QOS on 4451-X

Hello,  I have a problem: class-map match-all HTTS match protocol http match protocol secure-http!policy-map QOS class HTTS priority percent 10 class class-default random-detectpolicy-map int class class-default shape average 10000000 service-policy...

Power supply for Catalyst C2960CDP

Hello. Help me please. I am have Catalyst WS-C2960CPD-8PT-L, but can not found Power supply.. In description part no - PWR-ADPT=, But all photo in reseller web sites Power Supplys with round connector.. My Catalyst have 2 pin connector, see please at...

RAM usage on a Cisco 1811

Hey there! I've inherited an older network at a new job I just started at and am wanting to get some insight into some router performance issues we're currently experiencing. In general, websites are taking longer than they should to load. Anything f...

BGP issue

I am getting an issue that is a router has so many entries in bgp table but bgp route is blank. Can anyone specify how it is possible and how to configure it, so that no routes from bgp in routing table. Below is the situation. A>show ip protocols *...

Resolved! EIGRP "Query" & "SIA Query" Packet

Hello, Since in EIGRP a Query & a  SIA Query are 2  different packet types, would really want to know the differentiation  between EIGRP SIA Query & EIGRP Query and when either of these is  used by the Routers. I went through the documentation & boo...

OSPF LSA flooding

Hello, I have couple of questions regarding OSPF LSA flooding process.  I have four routers connected on a broadcast link (R1,R2,R3,R4). R1 and R2 are DR and BDR respectively and R3, R4 are nonDR/BDR routers. 1. If there is a change in a network conn...

zafar_118 by • Level 1
  • 2190 Views
  • 3 replies
  • 0 Helpful votes

Resolved! Sub-Interface question

So here's my question; do sub-interfaces automatically route traffic without a routing protocol enabled?  This is just one little detail either I missed or forgotten. interface Serial0/0 no ip address encapsulation frame-relay clock rate 2000000!in...

VPN Routing Issue

Hi everyone, My main office is set up with a 10.0.0.0/8 network. I just opened a secondary office which I'm trying to connect to our site to site vpn which is currently operating with 2 home offices with 192 class c networks. The new office I configu...

Load more