i have a simulated network of two branches connected to a internet service provider. i set up and configured vlans in each branch but in doing so the pcs in each branch can no longer access thier web server and the isp web server. tried setting up st...
Forum Posts
Resolved! Ethernet and VLAN overlapping
Hi,So I have a FastEthernet on my 2811 router which has 192.168.1.130 / 30 and DHCP pool which is in network 192.168.1.168 / 26. When I try to configure VLAN 10 which should have 192.168.1.169 / 26 it says that it overlaps with FastEthernet 0/0.... I...
I have been trying to limit SSH on a router and my ACL doesn't seem to be workingip access-list extended 10710 permit ip host 10.20.0.20 host 3.3.3.3 log15 permit ip host 10.20.0.20 host 4.4.4.4 log20 permit tcp host 10.20.0.20 host 4.4.4.4 eq 2225 p...
Resolved! Static routing problem
Hello all,I am doing a school project that requires me to do certain tasks in a network topology. Below I will list all the bullet points I think I have done right, and the ones I have trouble finishing up. If anyone has any advice, or thinks somethi...
Hey, I am a student and trying something out in packet tracer. I am creating a network and have some trouble with the HomeRouter.On my router, I got a network with a private SSID named "prive" with PSK "prive123" . I can connect to that LAN network. ...
Hi, I am trying to access my CUCM 11.0 using Winscp with SFTP but I got this error: What could be the issue here ? Thanks Mohammad
Related link: https://communities.cisco.com/docs/DOC-54368 I got a CGR1120 at rommon-1 with the following outputs: rommon-1> dir flash: cgr1000-universalk9-bundle.SPA.155-3.M5.bin cgr1000-universalk9-mz.SPA.155-2.T managed eem vlan.dat bootstrap: ...
Resolved! EIGRP metric calculation
Hi, Two routers, R1 and R2, are directly connected and are EIGRP neighbors. R1 redistributes static route. On R2 I am seeing the total delay of 410 microseconds for that redistributed static route. The R2's ingress interface on which the advertisemen...
Hello, This's the first time I'm implementing VXLAN in my network. Basically, we're talking about pair of witches, pointing each to the other. I'll have 2 such pairs. From what I've saw from Ciscos' documentation of VXLAN, setting multicast connectiv...
Hi I'm troubleshooting an atm/dsl interface on a 877 router. We have some problem whit CRC errors and Header errors. My problem is that I want to clear the counters(errors when "show dsl int atm 0"), I have tried:clear atmclear int atm 0clear counter...
Resolved! ISR 4331 | Power Supplies
Hello, I wanted to know if the ISR4331 supports dual power supplies or not. According to this Cisco platform datasheet, it shows that this particular model supports PSU0 and PSU1, which indicates to me that it DOES support dual power supplies. ci...
Hi Guys, I am trying to set up a lab a dhcp pool in a DHCP server where my dhcp server is located in CORP VRF and clients are in PUBLIC VRF. And there is no route leaking between the VRFs. Will it work ?? From Theory with Option 82 enabled it works b...
My ap can connect to the laptop but it doesn't get ip via dhcp but I don't see why. Can someone take a look at this. Must be coming from Router first floor on the left side. Adding the configurations done would be a very big help.Thanks in advance
Hey i am student and trying something out in packet tracer. I am creating a network and have some trouble with the WLC.I have made 3 vlans for Guest (Bezoekers), Users (Medewerkers), and Management (Directie).I can connect to the AP's with a laptop b...
I cannot connect to my LAPI don't understand why but my LAP is not getting IP address and I can't connect to the LAP(see Packtet tracer) with the PC From karine. The ip to get on the WLC is 192.220.4.1.If someone could take a look at this and possibl...
