Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
Labels

Forum Posts

Start a conversation

Resolved! vrrp configuration help

plz suggest me regarding vrrp  configuration. in my small organisation.. i have one isp currently . i want to configure the vrrp for redundancy .for that i'm planning to get 2nd link from different isp . but how will i configure my lan ip one 2 isp a...

Problem with Supervisor on Nexus 7k

Hi all,I have 2 supervisor 1 on Nexus 7K. Operate in active-standby. Today, I use show module command, I see that standby supervisor in fail state as bellow: CORE-NX7010-001# sh moduleMod  Ports  Module-Type                         Model             ...

what is best way to update CRS-1 IOS-XR software

Hello,    I know there 3 ways to update IOS XR on CRS-1:    1、install add    2、goldendisk    3、turboboot.   but in real job, for a , such as 2+4 multichassis enviroment, what is best way to update IOS XR on CRS-1   I haven't find detail update proced...

fly by • Level 2
  • 1636 Views
  • 9 replies
  • 0 Helpful votes

Resolved! router dsl connection

I need to order a small router, 2911, that will access a DSL.   What interfaces do I need?  Can ADSL use a standard ethernet port?

jimmyc_2 by • Level 1
  • 796 Views
  • 2 replies
  • 0 Helpful votes

Port speed and Wan speed

While reading Cisco documentation, router have a specific WAN speed up to 21 Mbps etc or more depending on router. You also see port speeds of 100Mbps or 1Gbps, but why are Wan speeds limited to far less on most Cisco routers.

Resolved! Routing internally to public IP Space

Hi guys, I am curious what the norm or suggested practice is for the following scenario: We have several internet egress points with several data centers interconnected over a private WAN.  Each data center has a variable block of Public IP. Currentl...

Resolved! Help setting up my network

Hi everyone,I am attempting a hands on project to cement several concepts for my CCNA and my MCSA and i am stuck at a certain point. I am implementing this setup within my own network for added functionality and practice. Furthur more i will be using...

Resolved! Dhcp IP via GRE Tunnel

Hey Guys,I have a question regarding the GRE Tunnel, simple GRE usually works for me but this time I have different requirements.We have 100 users in Australia, they would like to use my network in USA. so I define GRE Tunnel which is working fine bu...

Help needed choosing a new router

Hi there,Our company is in need of a new router for internet traffic. Because I'm having trouble selecting a model, I would like to ask for your help on this one. Our situation is as follows: - Primary internet connection is a 60/10 Mbps cable connec...

Cross VLAN traffic issue

I am having trouble getting my dev environment working properly. I am unable to get my ESXi server to communicate with my Windows Server on a separate VLAN. From the diagram below I want DLESXi2 to route via DEVDLSRV1 (on DLESXi1).I have tried assign...

PBR can't be assigned to vlan interface, why?

Hi guys,this is my first question, so thank you for support.I have one WS-C3750G-24TS-1U and one WS-C3750G-24T stacked, they run 12.2(55)SE7           C3750-IPSERVICESK9-M, the sdm tmeplate is desktop routing, I can configure policy map, but when I a...

LoadBalancing

Dear Team Cisco,I really wonder that when configure load balancing , does the speed combinetogether or not  in cisco 29121. Assume that i buy from 2 ISP1 link is 2Mbps, 2 link is 1Mbps, so after i configured load balancing so the speed gain 3Mbps rit...

Load more