Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...
Cisco offers a ISM-VPN-29 for 2901, but my reseller told me it would be cheaper to buy the bundle (CISCO2901-HSEC+/K9) than only the module and the HSEC license. http://www.cisco.com/en/US/prod/collateral/modules/ps2706/ps12202/data_sheet_c78-682436....
Hi AllI have a query related to Router replace in live network with minimum impact to customer.The Router could be any PE/P/ISP Exit Gateway in the Core NetworkSay We have two PEs working in a PoP and 500 customers connected to each PE....PE is havin...
Hi allI was wondering if anyone has successfully done something like this, if so, how? It could be that it's dead easy but I'm clearly missing the obvious.To try describe it as simple as I can I have the following scenario:<172.16.0.0/16 CORPORATE NE...
Hi AllI have to configure some new VLAN in our officeVLAN-1 --Server 192.168.0.0/24VLAN-2 --Systems 192.168.1.0/24VLAN-3 Project-1 192.168.2.0/24VLAN-4 project-2 192.168.3.0.24I want Proje...
Hi ,I've got heaps S route in my routing table which are the destination of VPN client.I tried clear ip route a.b.c.d , clear ip route *, this never clear.This cause VPN connection drop out.What should I do? It is headquater route,...
I have 2 routers joined together by their 0/1 Lan interfaces.Router A 0/0 Lan interface is hosting the public ip of say 178.0.0.0 255.255.255.248Router B is connected to Router A via the 0/1 as previously stated. I would like to add 178.0.0.1 to...
can you please tell me if it is possible to communicate from router A and B to the outside without declaring the networkAAAA and BBBB ... ZZZZ in the BGP routing table on Rouater A and B, knowing that I work internally with static routing ?
I could not log into the 871 (client had no password). I could not get the config-register setting. After resetting the password (I had to set the config-register to 0x142) I can no longer get the router to boot correctly (goes into RMON). Does anyon...
I have a problem I can not activate the commande1 card-type 0 0And I can not activate the Serial, and try in various slots of the router but does not workThe Router this command does not allow meThe IOS version flash0: C2900-universalk9-mz.SPA.151-4....
Hi,I have a 871 and when I'm downloading a bigger file (over 100 MB) or uploading via FTP the CPU goes to 99%. I have tested this with basic configuration (only nat and dhcp service configured). I have install the latest IOS version that is supported...
i am replacing 3700 with 3900.on 3700 i got WIC-1DSU-T1-V2 and i am replacing 3900 with VWIC3-2MFT-T1/E1 Pease let us know it will work or not.
Can someone clarify on the use of BGP update-source?My understanding was that BGP uses the IP address configured on the physical interface directly connected to the BGP peer as the source address when it establishes a BGP peering session. You would t...
Hi,I have recently purchased a secondhand HWIC-3G-GSM card. I have tried it in multiple 3845 and 2801 routers all running the correct versions of IOS. Everytime the router boots up I get the following error messages:*Sep 4 10:33:56.935: FPGA core lo...
I have setup aaa on my Cisco 3800 to an IAS Radius 2003 Server. Everything works but I want to configure the IAS to hand the privileges for the user logging in. Any ideas on how to do this?
Hi,I have an Cisco 850 router (c850-advsecurityk9-mz.124-15.T17). The router is able to take the following command.ip route 1.1.1.1 255.255.255.255 2.2.2.2 track 1It shows up n the running-config#show run | inc ip route 1.1.1.1ip route 1.1.1.1 255.25...
