Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

“Webinar

 
Labels

Forum Posts

Start a conversation

cisco 1841 port translation not working

Hi all, I have an 1841 for a test environment and I've been trying to get port translation to work and I just can't get it to work.  I can get to the router via Telnet or SSh no problem, but nothing internal.  My scrubbed config is below, thanks in a...

Resolved! Erasing flash memory on active router?

Good afternoon all.In a nut shell I have purchased a 2801 router running CME from someone.  When i show the contents of the flash memory there are over 100 files.  I appreciate the *.bin file for the IOS and the *.tar file for installation of CME are...

Resolved! Upgrading from IOS release 12.4 to 15

I currently am supporting a 3845 running 12.2.24.T on one side of an MPLS circuit and then a 3825 running 12.4.23 Mainline on the other end of the circuit.I was reading the Q  & A section about release 15 M and T.  Is there any reason (other than har...

Router 1921 crypto issue

One of my client try to configure the crypto key,but the router is not taking the command.What can be the issue...Router has security and data base license installed.Router detail is attached in snap.

Resolved! OSPF: Router process 1 is not running

Hi,I have created an OSPF ring between three routers for redundancy. Yesterday we had one of our link failed and found that the traffic didn't take next available path instead the site was disconnected. When checked on the routers I found that the hu...

suntecsbs by • Level 1
  • 11517 Views
  • 2 replies
  • 0 Helpful votes

IPV6 Summary address

Please, look at the three IPV6 addresses below.2001:0DB8:0:0:7::/64 2001:0DB8:0:0:8::/64 2001:0DB8:0:0:9::/64 The book I am reading says the summary of the three addresses is 2001:0DB8::/48.I thought the summary would be 2001:0DB8::/64.  If I am wron...

jaighobahi by • Level 1
  • 12154 Views
  • 2 replies
  • 0 Helpful votes

QOS to limit outbound traffic to DSL

Setup:Cisco Catalyst 2970G 28Port Gigabit Switch WS-C2970G-24TS-EGigabitEthernet0/1 connected to DSL equipement connecting to the InternetGigabitEthernet0/9 connected to the network that is to limit its equipments outbound Internet speed.This is what...

AlbyWRX by • Level 1
  • 745 Views
  • 1 replies
  • 0 Helpful votes

IP HELPER in VLAN

Greetings AllI am getting problem in IP helper commands.I issue commands on Interfaces but did not get IP from DHCP Pool of Router.Router acting as DHCP---3750---3750--Router as DHCP Client.Vlan is Up/Up.Alreday done shut /no shut  on All interfaces....

Resolved! Tacacs not loging

Hi, I have implemented OSPF and configured tacacs server for central logging and it worked fine. Now, I have changed the dynamic routing protocol to EIGRP but I couldn't get the username and password screen while trying to loging to router. When I tr...

Mero Cisco by • Level 1
  • 3130 Views
  • 10 replies
  • 0 Helpful votes

Resolved! Eigrp variance control

hi,i have only one path to reach router 3 loop int i.e 172.172.172.3. via serial 2/0, the FD distance is 2297856 and  i  try to increase the fd cost to add other another path to reach r3 loop. after i increase the 1000 fd now it change to  2298856. i...

feroz syed by • Level 3
  • 1024 Views
  • 10 replies
  • 0 Helpful votes

3662 Router Does Not Reboot

I am having what I consider a pretty serious issue with a Cisco 3662 Router here... in one word the router does not reboot!Here is what happens:Router#reloadProceed with reload? [confirm]*Mar 1 00:22:57.399: %SYS-5-RELOAD: Reload requested by admin ...

Configuration PFR for Internet Load Sharing

Hello EverybodyI´m a new fan of the PFR technologie, i´m some difficultie for set the learning mode.Here is the scenario, i have one 2 routers connecting to 4 ISP, each border router have 2 ISP or 2 External link So my goal is to set a kind of load s...

Resolved! DMVPN Traceroute hits hub then spoke !!

Hi Folk , Greetings .. I have followed the lab posted underhttps://supportforums.cisco.com/docs/DOC-29434 exactly bit by bit and also illustrated below for brevity , but the problem when I do traceroute from one spoke to another spoke , then traffic ...

View All
Review Cisco Networking for a $25 gift card