Routing

External IP not pingable from outside

Hi guys,We have a cisco 2811 router with 2 ADSL interfaces. One dialer interface is used for internet and another dialer interface is used for VPN. The dialer interface that is used for internet purpose is "Dialer 1" and the VPN is "Dialer 2". The ro...

Resolved! ip sla feature

c1900-universalk9-mz.SPA.152-4.M2.bin....my this image is supporting a ip sla feature.But c1900-universalk9-mz.SPA.152-4.M1.bin image is not supporting the ip sla feature.is i need to upgrade the image or i need any license to install in router?

7206 VXR configuration to pass MPLS Traffic

I have a 7206 VXR router between a several Mikrotik routers on our backbone. We have the Mikrotiks on both sides of the CIsco 7206VXR setup for MPLS/VPLS. I need to simply setup the 7206 to pass the MPLS/VPLS tagged packets to the next router on th...

Resolved! ISP IP and Customer IP on same router

*We have a Cisco 1921 Router (2 GigabitEthernet router interfaces)Our ISP gave us one of their public IP addresses to communicate with their equipment, and a set of our own public IP addresses. They want us to assign their public IP on the internet ...

Cisco 2801 VWIC Frame Relay Layer 2 problem interface up/down lmi deleted

Hello,I need a another set of eyes on this issue. I am building a frame relay cloud with a 3725 as the frame relay switch, 2 2691 as remote sites and 1 2801 as the other remote site. The 2691s are working and connected but the 2801 interface stays in...

Resolved! show controllers vdsl 0 - explanation

Hi, Could anyone please explain the difference between the "Attainable Rate " & "Speed" parameeters obtained from "show controllers vdsl 0".Could you also advise me on any place where I could have an explanation on the output received from the above...

Cannot get outside access

I have my router setup with a gig 0/1 as my primary interface and I'm using cellular as a backup. However, I cannot get outside accessMWA-CTT#sh runBuilding configuration...Current configuration : 2596 bytes!! Last configuration change at 19:24:01 U...

RITE traffic-export for ipv6

we've been using RITE extensively in our networking labs.we' now are experimenting w/ ipv6.we see no ipv6 traffic.is there any special config required for the traffic export feature function for ipv6?tnxams

Resolved! SRR egress configuration

Hi,I have tried to set the following config on interface:srr-queue bandwidth share 10 10 10 10 srr-queue bandwidth shape 10 20 5 5But does it make sense? Shaper for 3rd queue is 5 but shared weight is 10!!! What takes precedence?

Resolved! Strange problem with route selection when using eBGP and EIGRP

I have a mixed WAN environment with both eBGP and EIGRP routes. The BGP routes should always take precedence, when they exist. If no BGP routes exist I want the router to fail over to using the EIGRP routes. So far, this works fine.The problem is,...

QoS vlan traffic not getting policed

I was trying to rate limit a vlan and found this works a ltitle different than a normal port. The vlan connections are still able to get full bandwidth bypassing this policer. I'm not sure why.class-map match-all BYOD-Accesslist match access-group...

qos exceeding more that 100 percent

hello ,I have a p2p interface interconnecting two sites and its bandwidth is 1536 kbps.I have applied LLQ on both sides of the link with a shape average to 95 percentage of CIR.I am still seeing the utilization exceeding more than 100 percentages in ...

HSRP & Routing

Hello all,I have a question regarding routing with HSRP. We have two ASR1001s; one is used for our primary Internet and the 2nd is used for our backup Internet. I was wondering if it is possible to point a network device, such as a firewall, to use...

Too much traffic on interface. Link L2 between SW4500-SW6500

Hi everyone, i hope anyone can help me with a problem of a LINK L2, Between SW4500 and SW6500.I have experience too much traffic between the link L2 (Fastethernet - GigabitEthernet),, 90%. What can I do to fix that, any command? rate-limit or someth...

Resolved! How to see what ISIS routes im receiving when OSPF is preferred?

How can I see what routes are being sent to me via one routing protocol when another is being prefered?For example.I have both OSPF and IS-IS running.When OSPF is preffered ISIS routes dont appear in a "sh ip route isis"I can see the OSPF ones in a n...