Greetings.This should be a really easy one.Im a cisco newbie. Well this is implied based on the simplicity of my question...Im trying to use an inbound access list on my OUTSIDE interface (with NAT) to limit access to specific servers, protocols, po...
I have being trying to config this router Cisco 867 VAE K9 for a while now.since i am quite new to data, i m finding it a little difficut to configure the router.I have a belkin router at home which i use for internet (pppoe)I would like to know the ...
I am trying to set up two groups in my company's Cisco ISA570w Router. One group is going to be open to the general Internet, while the other group will have common social and video sites blocked. I would like to be able to block by MAC address if ...
I see that most Cisco Routers have a recommended user specification but I cannot find one for the 1941W, does anyone know what the recommend (maximum) user rating is for this router?
hi i have a cisco 1941 series router which i am trying to connect but need help setting it up.I have my netgear modem router which is connected to the internet and i the cisco router connected to the netgear modem router on port GigabitEthernet0/0 wh...
I have been using the Cisco7613 chassis with PA-MCX-8TE1 module for TDM LSL. (IOS version is 12.2IXH1)To prevent the detect that transient connection lost, I has configured to Carrier-Delay function at serial interface.But it was no effect. because i...
Hi All.My router is connecting fine over ADSL but xbox is reporting moderate/strict NAT. Has anyone come across the issue and fixed it?Xbox is being leased an ip from routers DHCP pool (192.168.0 /24).I believe it involves some port forwards? but ca...
Hi, I am new to ppp, and have so much confusion about authentication. I have read many articles and threads, but my doubt is not cleared. Unfortunately, cisco documentation is not clear on many aspects. R1 and R2 are connected back to back. I w...
Hello,This router was running fine since a few years.We had to do an electric maintenance yesterday morning and the router had to be electrically shutdown.When rebooted it started crashing systematically after booting.We've tried to remove linecards,...
Hi to all. Please help. I had this topology:Problems:1. Can`t connect from WAN to IP=X by nating rule to IP=C (NLB MS)2. Can`t create NAT rule from ISP=2 IP=Y to IP=C, telling you have NAT rule form ISP#1I thought that have some miss rules in acl lis...
Hi,I've labed l2TPv2 over a WAN connection and it seems to work fine. So far I have only configured one VLAN to traverse the L2TPv3 tunnel. There are a couple of VLANs that I would like to send across the WAN. Could I configure several L2TPv3 tunnels...
Dear all, Wonder if anyone encounter same situation of me. I build a Dual Hub Dual DMVPN with OSPF and I observed that the ospf hello packet are not arriving hub from spoke. Thus my ospf neighbor periodically up/down while the timer excee...
Hello,Does someone has an manuel for me to configure vpn with windows clients?Thanks a lotBest regards Tobias
I updated the firmware on my rv220w router to the latest 1.04.17. I am now getting the following errer every 3 to 15 minutes. "PLATFORM [System] /pfrm2.0/bin/bwLimitConfig /tmp/system.db 18 dot11STA 8 failed. status=-1". what do...
Hello,I am new here so thanks in advance for any help.I recently purchased a 2921 to replace an aging router.We will using this router specifically for T1 data connections only. I am maxing this router out with T1 WIC CSU/DSU cards.I have 4- VWIC3-4M...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 06-14-2025 01:24 AM | ||
| 05-12-2025 03:28 PM | ||
| 05-09-2025 02:25 PM | ||
| 05-05-2025 11:47 PM | ||
| 04-22-2025 12:20 PM |
| User | Count |
|---|---|
| 9 | |
| 7 | |
| 4 | |
| 4 | |
| 3 |
