In what scenario is two way NAT used?
In what scenario is two way NAT used?
Hi,I followed this lab: https://packetlife.net/blog/2010/mar/29/inter-vrf-routing-vrf-lite/ .However, at the final stage, BGP to OSPF redistribution is not working. Everything else is working fine.This is my configuration on S1:ip vrf Blue rd 65000:...
I don't have a lot of experience with ACLs and I am trying to create an ACL on a switch that will block a specific subnet from accessing the other networks on the switch.Network management IP of switches 10.0.22.0/23switch A Mgmt IP 10.0.22.1Switch L...
We have a site to site VPN tunnel setup between the two ASAs, on the switches the ip route 0/0 goes to the firewall. We will be adding a point to point connect between the two switches, would it be an issue if I have both of them running at the same...
im rather new to networking and just learned about static routing. Right now im trying to route the network address of a smoke detector to this router but it fails. All the other ips i used works but this. The network addresses are such: 192.168...
Hello,You guys were an awesoem help with previous questions so I have one more. We are about to start learning ACL but first we have to build the network and they should ping. Instructor gave us a network of 10.1.0.0 255.255.255.0 He said to use OSP...
Hey everyone,I'm kind of a beginner but I am hoping someone can help me with this..So, I'm in the process of setting up an isolated test lab using a Cisco 881 IOS router and a L3 Netgear 16 port switch and one simple VLAN (VLAN2) (created on the 881)...
Running into an issue that I cannot figure out and looking for help. Cable modem (bridge mode) -> 1921 router -> 3750 switch -> computers No devices can ping the default gateway:10.5.104.1 The router config was built by another tech but worked at th...
Hi,I created a vlan because our Ip address range is running out. The network is working internally. But i want to step an IPsec tunnel for our azure. The Vlan can't access azure virtual machine. Is there any way to create an IPsec tunnel with that vl...
I have 3 Vlans on my network Vlan 1 = 10.76.x.x Vlan 2 = 172.16.x.x and Vlan 3 = 192.168.x.x, my question, I noticed that my loopback addresses on the switches are on the 192.168.X.X network and I wanted to use that for my Vlan 3. What is the best Pr...
GIVEN: (obfuscated) NEXUS-9300# sh ip int br vrf allIP Interface Status for VRF "default"(1)Vlan30 172.16.1.5 protocol-up/link-up/admin-upVlan172 172.17.2.2 protocol-up/link-up/admin-upVlan200 172.16.3.8 protocol-up/link-up/admin-upVlan300 172.16.3.9...
Hi,I have configured BFD on 7609 router and other remote end is Huawei. But BFD is not getting UP. Following are results at my side. Can any one help in this case. NeighAddr LD/RD RH/RS State Int58.27.222.70 ...
I need to create a static ipsec VTI (on ISR4k/IOS-XE) which will connect to a Fortigate at the far end. DPD is switched off at the far side and I don't have any control over it. The tunnel will have a static route /24 pointing towards it and this wil...
My customer needs fax support on the router so ordering FXS port. Do we need add PVDM or it is built-in like 4K router?
I cannot get the firewall to provide dhcp after trying several options. I tried using it as the ip router, the default gateway with no success unfortunately. I would prefer getting it from the DC but management wants it strictly from the firewall.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-15-2024 05:07 AM | ||
07-13-2024 09:04 AM | ||
07-09-2024 05:41 AM | ||
07-03-2024 08:54 PM | ||
07-02-2024 04:20 AM |
User | Count |
---|---|
16 | |
4 | |
4 | |
4 | |
3 |