I have configured a test lab with BGP. I have two different AS setup with dual connections between the systems. I configured the loopbacks and update-source between the AS but BGP did not become active until I changed the ebgp-multihop count from def...
Dear ALL,I am getting below logs from one of the cisco router but not able to understand.Any one please help me understand the same-- Router is sending below logs from IP 1.0.0.0, but this IP is not configured anywhere in router... %TRAP [0]172.22.7....
Hello,I need another set of eyes on my config. I am trying to set up my router for a basic connection for the time being. I set my gig 0/0 port to dhcp I see traffic being sent and recieved but I can not ping 8.8.8.8. I am connected to a basic comcas...
hi,can you pls explain meaning of log , the specified Router connecting Leased line to Head office
Hi, I am trying the following configuration in GNS3. I am not able to figure out what is the problem. Your help is highly appreciated.R1-R2-R3-R4R1-R2 ---> ebgp, R1 is in AS 200 and R2 in AS 100R2-R3 ----> ibgpR3-R4 ----> ibgpI redistributed few r...
Dear experts,I need to do a load balance between 02 MPLS's link, but is not totaly balance, because my client want that only one specific application (Terminal Service) go to on link, the rest of traffic have to go to another link.I was tried to do t...
everybody,i need the part number of the DRAM Memory of cisco2851 router.i need part number for 512MB and 256MB DDR RAM of cisco2851.kuku
Hello everyone, I just wanted to ask for your help to undersstand the following route-map behaviour.I'm doing some redistribution labs and I have the following scenario. { (EIGRP 100) R4 ----- [ R2 } ------ R1 (OSPF) ]R2 sits between EIGRP and OSPF ...
Hello!We've got cisco881w and now it reached it's brandwidth and we decided to change it to asa5505I've never configured such devices and I got used to iOS and it's very difficult to get used to it's syntaxesConfig of 811 here:version 15.1no service ...
Dear all,I would like configure two router (e.g. 1921) back to back via a 2 pin copper wire. Can I use HWIC-4SHDSL-E card to do it? What is the configuration I can use? Any sample configuration can be provided ?Thanks!
I apologize if this is a duplicate post. I looked but didn't find anything. I'm looking for a configuration guide, similar to the ASA Configuration Guide, that that can provide documentation on how to configure a Cisco 3925e router. I have my CCNA an...
Good afternoon!I would be very thankful if someone could help me out with a simple question, that made me stuck.I have Cisco 2910 router that have 3 interfaces:g0/0 - LANg0/1 - WAN1g0/2 - WAN2I would like to configure port forwarding in such way that...
Hello Guyscan any one Help me the below scenerioSceniuor1- Cisco Router Eth0/0 : Ip address 192.168.1.1 /24 == connected my laptop of 192.168.1.2Eth0/1: Ip address : 192.168.2.1 /24 = connected cisco swith 2 - Cisco Switch VLAN 2 Name : Sales : i...
We have a corporate site with an Internet DS3 line and doing BGP peering with this ISP with our own registered AS number and public /25 IP addresses (for example 192.168.200.0/25). A remote office is connected to our corporate office via private 1 GB...
Hi.I installed mpls feature set in N7K.I was able to enable feature l3vpn.Then, I tried enabling feature ldp.It gave me an error of:# feature mpls ldp TRANSPORT_SERVICES_PKG license not installed. ldp feature will be shut down after grace period of a...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 05-23-2025 07:04 AM | ||
| 05-23-2025 06:19 AM | ||
| 05-23-2025 03:37 AM | ||
| 05-22-2025 11:35 PM | ||
| 05-22-2025 10:50 PM |
| User | Count |
|---|---|
| 4 | |
| 3 | |
| 2 | |
| 2 | |
| 1 |
