Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Labels

Forum Posts

Start a conversation

Image Questions

  Hi,I'm going to start using 3750Xs PoE switchs. I know with the 3750s the images choice was ip base or ipservices. What are the parallels to the 3750x switches?Thanks, Pat.

Resolved! Inter vlan Routing does not work

Dear boss I have cisco 3845 router  and 4507 & 2960 switch.  I have 4 Vlans on 4507  and connected to router on  four ports. Its working fine.Now i want to create another vlan ( vlan 15 ) that trunk with vlan 20 and router port f0/0/1. i.e router F ...

Resolved! QoS for Exchange

Hello everyone, I have a hub router at my data center serving approx. 90 spokes. While my infrastucture is implementing spoke-to-spoke tunnels for inter-branch communication, all my application servers are still behind the hub router at the data cent...

Ricky S by • Level 3
  • 2911 Views
  • 5 replies
  • 0 Helpful votes

Resolved! Help to create frame-relay multilink PPP

Hi,I would like to know if it is possible to build  a frame-relay multiplink PPP on more than one interface. In other words, could we aggregate two serial port and build a single bundle of frame-relay multilink PPP and keep the same map-class frame-r...

Steph1963 by • Level 1
  • 1494 Views
  • 3 replies
  • 0 Helpful votes

Resolved! BGP ASN 32 bits on IOS 12.4(24)T

Hello guys, I'm trying to establish a BGP neighborship with my ISP using my own ASN. The thing is that AS is a 32bit AS. I read on others papers that since the IOS 12.4(24) the support for ASN 4byte(32bits) was introduced. For some reason I cant enab...

victorhdss by • Level 1
  • 11174 Views
  • 6 replies
  • 0 Helpful votes

Resolved! ASA 5510 8.3 Inter-Vlan routing with NAT

Hello,I have found multiple solutions to this question for < 8.2 but no solutions for the new way the ASA does nat statmentsBasically i have multiple VLAN's and i need 2 of them to communicateinside - 192.168.1.0/24 ( security-level 100 )voice - 192....

Resolved! Branch router suggestion with dual-power

Hey folks, we have a client request to deploy a router connecting them to our network. Our client is one of the large telecommunication providers therefore they want all the bells and whistles which includes a router with redundant power built-in. Ca...

Ricky S by • Level 3
  • 1438 Views
  • 4 replies
  • 0 Helpful votes

Resolved! RPS2300 with 2900 routers

Hello,I want to connect a RPS2300 to a Cisco 2911 router to provide power backup.I have two questions :1 - Easy one : if the 2911 PSU (internal Power Supply Unit) fails, can anyone confirm me the RPS2300 provides power to the 2911 with no reboot of t...

Router for low load server room

Which Cisco router would be preffered for small server room with:20 VLANS with average overall traffic about 150 Mbps20 IPSec tunnels with overall traffic about 20 Mbps2 BGP peers (ISPs with failover, without load sharing - with only default route co...

DavisNT86 by • Level 1
  • 422 Views
  • 1 replies
  • 0 Helpful votes

ACS and Switch Lockups

Hi All,We are having a problem with our ACS and switch configuration.Basically if the switches lose connectivity to the ACS server the switches completely lock up, you can’t even console onto the switches.We want them to use the fall back username an...

Inside NAT to NAT help

I'm trying to get (what I'm guessing is) inside NAT to NAT working. The users need to be able to RDP to a term serv by using the external WAN IP address only. So whether they are internal or external, they would use the WAN IP to access the terminal ...

Resolved! BGP with 4 ISP

Hello All,I have Switch 6509E wich is the core of the network, and we have 4 llink form 4 ISPs, all the link will work at the same time,could please help to configure, how can I confiugure the BGP , as I know if I configure bgp it will work with one ...

Load more