hi,i got a spare SPA-1X10GE-L-V2 and would like to insert/use this 1x 10G module/card in a spare slot in ASR1002-x.my question is, is this OIR/hot swap module that ASR1002-x will auto recognize?or do i need to reload ASR1002-x for the module to be de...
Forum Posts
Hello, What would be the command to issue on a router to check all the commands that have been entered on it. Thanks!
So I'm doing a lab, and setting up a mpls core. I had to troubleshoot my lab as the config was wrong. So I have a connection between R6 and Switch 4, which is a trunk. When I try to ping R6 from R1 it doesn't work. Now I change the trunk lik to an a...
Resolved! Performance Xconnect with l2tp over wan
Hi, I have two isr4331 with isp channel about 300 mbit, and I needed to connect two vlans, I decided to use xconnect over l2tpv3 with ipsec and after configuring and testing I noticed that with 100 mbit traffic qfp = 70-80%, is it normal for xconnect...
Hello,we have a couple of CBS350, and after Updating them to Version 3.3.x we where no longer able to access the VLAN IP Interface from outside of the subnet.I have tried back and forth with:- default route- ip routing- VLAN Allow lists- No Access-Li...
ASR 1002-X Version 17.6.2 Unable to use the "ip idle-group X (in|out)" when creating a virtual template on an ASR, this was available on older IOS routers. Example config: interface Virtual-Template10ip idle-group 1 inppp timeout idle 60!Access-li...
can you please help , how can i enable webUi in cisco 4221 router for ISP configure
Resolved! OSPF to RIP to OSPF again
Hello,I'm having trouble with a network that I had to implement. In OSPFv2, let's say we have the area 0, this area is supposed to have an other area, area 2, directly connected. Everything works fine but then we put an other subnet that is configure...
I have changed the MTU on R2 interface (Gi0/0/0) from default (1500) to 1300 but its neighborship still showing in Full state it should be EXSTART state .what happened wrong , kindly share your views . i am sharing all related configs on both routers...
Buenas con todos, queria que me ayuden en este problema, lo que pasa es que en este LAB, me pide el R2 como servidor DHCP, el cual ya lo elabore, el R1 es un loopback como simulador de internet, en el cual todo me salio perfecto, ya que hice ping a t...
I have a C3925 router and its working fine. I try to go to its webpage at 192.168.69.1 and I get a blank screen no matter which browser I use. I know there should be a limited page that I should see.I do have CME GUI installed on the router and whe...
Hello,Needing help as my CBR LAN is unable to ping my AUS DMZ, I notice the ASA Firewall can ping the DMZ but it can't ping the LAN. I'm not finished with my network so in the VLSM table I provide many things that are not included in the packet trace...
I have a scenario where I need to NAT a 10.0.0.0 /24 network coming into my routers tunnel 1 interface to a single IP and have yet been successful in doing so unless I do nat overload and define the tunnel 1 interface as ip nat inside and then my gi ...
at present i am having Cisco ISR 4331 running IOS 16.6.4. I want to increase the nat translations total from 131400 to 200000 , in order to do so should i increase the value using ip nat translation max-entries 200000 or ip nat translation max-entri...
Doing some labs and the configs are going: router eigrp xxxxxxaddress-family ipv4 unicast autonomous-system 150topology baseexit-af-topologynetwork 192.11.11.11 0.0.0.0 abd so i wonder what's the poing of the topology base command, if anyone can hel...
