Hello Colleagues,I would like to check one small thing about new Cisco router C8500L-8S4X. I have checked all possible tools and available documents but there is no clear answers anywhere. Does it support GLBP - Gateway Load Balancing Protocol? From ...
Hi,can one node be a map server/resolver, and a proxy ITR/ETR? Or proxy ITR and ETR need to be sepparated on different nodes?I am referring when border and control plane nodes are colocated.
I have a cisco 9300 switch that for some reason I can putty into from one ip scheme and not from another, this was working up until yesterday not sure what changed but when I connect from the computer that isn't working i get a refused error when I t...
Egress equipment—core—Access Equipment—Client; now the egress equipment needs to do a cold standby, the equipment is CISCO2921/K9, after the configuration can not access the external network. The situation is as follows:1: The client can ping the WAN...
what is configuration for adding in CMBD ,SMC , OBS for cisco cisco switch
Hi,I have three routers: R1 --(eigrp)-- R2 --(bgp)-- R3. On R2 I am doing redistribution from EIGRP to BGP. Routing table on R2 looks like this:D 1.1.1.0 [90/130816] via 192.168.0.1, 00:03:11, GigabitEthernet0/0So this is pointing to R1.If I c...
Hi,I will reffer to the following topology: I am trying to identify scenarios in which loop or sub-optimal routing will occur due to different routing protocols and redistribution. I am presuming OSPF of EIGRP under IGP with standard AD.So far, I hav...
Hi all, i have a question about importing routes inside a vrf Right now, in vrf red i'm importing some routes from global routing table and also from vrf blue vrf definition bluerd 1:4102!address-family ipv4route-target export 1:4102exit-address-fami...
I have two devices a firewall and cisco router. Firewall has two IPs public and a point to point /30 network that connects to the router. The router has the /30 and the LAN network. Nat outside is through the /30 interface but when I create a static ...
I'm trying to upgrade from 16.06.09 to 17.06.05 on my 4321 router Using this command to initiate the upgrade. install add file bootflash:isr4300-universalk9.17.06.05.SPA.bin activate commit The error I'm getting is below. It looks like it is a space ...
Hi. I have a virtual Firepower Management Center and an FTD-1010 on which I've configured a site-to-site VPN for SIP traffic.The tunnel is up and I have a NAT rule configured but, when I perform a packet trace, I'm getting the error:Drop-reason: (ins...
Hello,I'm using a CBS350-48T-4G, and i want to get by snmp the cpu and ram usage on it. but i can't find the correct oid to get those informations. Is it even available?
I'm replacing an old edge device with two Cisco 8300 routers; Dual ISP setup. The 8300 routers were also ordered with 4 port LAN modules. I'm putting together the config before the routers have arrived and want to figure out the down stream config. ...
Hello. Our spoke ISP failed for 4 minutes. Once it returned, our C2921 DMVPN spoke remained in the NHRP state (no production traffic flowed from this spoke to the hub. This was remediated by shutting then no-shutting the spoke tunnel interface (It wa...
Hi guys,I noticed that from last week, I am getting practically every minute or less, a log message like this in ASR log:Jul 26 2023 14:26:46.158: %IOSXE-5-PLATFORM: F0: cpp_cp: QFP:0.1 Thread:199 TS:00084795299536916500 %PUNT_INJECT-5-DROP_PUNT_CAUS...
