Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Bookmark
|
Subscribe
|

Labels

Forum Posts

Expertise,I cannot view all the  logs on the router. Logs are there for just 10 mins ago events. Is there any way to see if interface was down, or line protocol was down before 20 - 30 minutes ago by some other way. I saw interface reset but that cou...

get_rthym by Level 1
  • 556 Views
  • 1 replies
  • 0 Helpful votes

IOS  15.1(4)M1.I am trying to setup my new 2901 running  15.1(4)M1 for frame realy via a VWIC3-1MFT-T1/E1 card.  Now I have set up plenty of frame relay connections via older serial cards, but I just cannot find any documentation on how to do this on...

joerggrau by Level 1
  • 2434 Views
  • 1 replies
  • 0 Helpful votes

Have a new 3945 router and trying to install a NM-HDV2-1T1/E1 card.  Card is not being recognized in the show inventory or show diagnostic command.  In the boot up sequence I see a %PA-3-NOTSUPPORTED: PA in slot4 (Unknown (type 987)) is not supported...

CNRH RDC by Level 1
  • 1730 Views
  • 5 replies
  • 0 Helpful votes

I have a router learning a default route from a neighbor OSPF router. The database entry looks as follows:Router#sh ip ospf data ext 0.0.0.0            OSPF Router with ID (1.1.1.1) (Process ID 100)                Type-5 AS External Link States  LS a...

AJ Cruz by Level 3
  • 1144 Views
  • 4 replies
  • 0 Helpful votes

Hi,I configured a 1841 router that connects to a DSL modem. This DSL connection is our Internet connection for vendor and IT testing. I have connectivity to the Internet using nat and have configured the router to act as a DHCP server. It seems to be...

Hello,I have a remote customer who is having issues with their 3825 router - since I can't be on site troubleshooting is difficult but so far all that seems to happen when the device is powered on is the "SYS PWR" light goes solid green, and no other...

Hi Friends...I have a cisco catalyst 2960 switch and i updated ios v-12.2 to 15.0.my switch is running with vlans..in other words i installed cisco SDM v.2.5.but i am unable to run the sdm... plz tell me any configuration is required in both (switch ...

Book suggests to use exit interface instead of using next-hop ip address. But while preparing for exam i noticed next-hop address is configured especially when configuring default route on edge router towards ISP. In what other situations we prefer n...

fb_webuser by Level 6
  • 11384 Views
  • 5 replies
  • 5 Helpful votes

HiWhen two Routers  Models  1941 (Main Router)    and  1841 work connected with HSRP,   and  a second LAN card is added to each one of themIf  i connect  the  GE 0/1  and  Fe 0/1   of each of one of them   To FireWall1 (in cluster with FireWall2)ANDi...

Arielstu1 by Level 1
  • 699 Views
  • 2 replies
  • 0 Helpful votes

I have a customer who needs to be able to do port forwarding so his branch sites can log into virtual machines.  They currently have a Cisco 877 router which was installed by someone else.  I have no idea how to work it or if this is even possible on...

derbygull by Level 1
  • 1259 Views
  • 2 replies
  • 0 Helpful votes

Hello All -I'm trying to limit available upload bandwidth on one of our Ethernet Customers off a 3550 switch running 12.2 .I recently tried applying a service-policy input to an interface, but it doesn't seem to limit the upload bandwidth.  I was abl...