Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...
All,How can I see a layer 3 port bandwidth usage? I have tried but it is not working.Thanks, 30 second input rate 0 bits/sec, 0 packets/sec 30 second output rate 0 bits/sec, 0 packets/sec L3 in Switched: ucast: 54217685 pkt, 15613598253 bytes - mcast...
Hi,I have the below config:!class VOIP match protocol rtppolicy-map QOS class VOIP priority 64!interface Tunnel255 ip address 10.255.255.4 255.255.255.0 ip nhrp authentication UbSmEbK ip nhrp map 10.255.255.1 172.80.2.2 ip nhrp network-id 255 i...
Hi to all, could somebody explain me, please, what is the last version in 3.x train of PDSN for MWAM? There are 3.0 version and 3.5, 3.5 - is an update to 3.0 with new features and bugfixes? Or these trains (3.0, 3.5) exist separately with own bugfix...
OK, I got m first bit of Cisco kit yesterday (857 ADSL Router) and I've got stuck on some routing stuff:The 857 has port 80 open for our webserver and this can be accessed externally without a problem. However, accessing it internally, via the www.ou...
Hi,I want to configure PBR on cisco router. That router is connected to 2 cisco ASA with 2 different ISP's.FW1 FW2 |_________| | RO | ServerDefault route for router is FW1. Various vlans are configured and int...
Hi,I have internal network 192.168.1.x. I have ASA haivng public IP range 50.50.50.0/24.My requirement is, whenever internal host 192.168.1.1 wants to talk to external server 200.200.200.0/24, source address should translate to 50.50.50.1.I have done...
hi, im having cisco 3660 cisco router.im connected my router through console cable in windows hyperterminal but there no output in hyperterminal.i changed baud rate and everything but there is no display.i tried by hyperminal,putty,teraterm etc.Pl...
Dear All,I would like to ask you some question about two command are different crypto map mymap 10 ipsec−isakmp and crypto map mymap 20 ipsec−isakmp.1- What are different on this commnad?2- Why we need to follow two command as below:no ip route−cache...
Hi,Can someone help me for simulating the Nexus OS,Does GNS3 supports Nexus OS simulation, or any other application is required.Please let me know.ThanksTabrez
Hello,I have a cisco router 18XX series with 2 fastethernet ports,1 console,1 AUX. ISP has dropped 1 ethernet cable to branch office for internet connection, I want to configure a PPPOE on ethernet interface to connect to internet.Can anybody link me...
I am assisting a customer with configuring their Cisco 1811 for internet and site to site communication over a Metro Ethernet circuit - basically it is a layer 2 connection at each site that connects them together.Each site has its own separate class...
Hello!Does ESR 10008 router support NetFlow Sampling? I want to lower netflow export proccess CPU load by (for instance) exporting with packet interval 100 or more.CPU utilization for five seconds: 38%/20%; one minute: 45%; five minutes: 46%PID Runti...
HiI've just had a new WAN link installed (OC3). I'd like some input in how I can test this circuit for latency, bacndwidth etc.. This is my first time I'm doing this so I don't know what I should look out for and what tools I should use.Any help is a...
Hello,I am runnig MST (Multiple instance spanning tree) in my network. When I connect switch with Rapid STP at the edge of MST region, status of spanning tree on that link depends on the connected device.for instance:MST REGION SWITCH <----> CATALYST...
Hi, allI have a Catalyst3750 with IPSERVICESK9-M-12.2(50)SE3 . I change OSPF network type from broadcast to nbma on a SVI, and I put the "priority 0" under SVI as the following. ip ospf network non-broadcastip ospf hello-interval 10ip ospf priority 0...
.jpg "VIP Mentor"){kind=icon}
.jpg "Hall of Fame Master"){kind=icon}
