Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

I have a small wireless isp. I have been trying to connect a catalyst 2950 switch to a cisco 1841 router which is connected to a t1 line. It is a managed router from my t1 provider. The 1841 has a static ip of 12.xxx.xxx.129  255.255.255.128 and a la...

Hello all,I have a question about a merged configuration which I attempted to get working recently with no luck. Our organization has a 1841 router which is it's primary router to ISP#1. This was a T1 connection which was being overworked by all of o...

Hi,When i try to ping my router i get the U caracter :>>Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 80.125.46.36, timeout is 2 seconds:U.U.USuccess rate is 0 percent (0/5)>>but i can access via telnet to this device.Does someone k...

Ayad by Level 1
  • 631 Views
  • 1 replies
  • 0 Helpful votes

Dear i have some doubtsI have two isp and connected to core switch and in core switch i connected bluecoat for proxy.   And I have 8 vlans.The issue is that i need to block internet without proxy, if any one want to access internet it should goes thr...

Hello All,This might be a silly question but i need verification. Given the configuration belowClass map realtime (match any)match (real time voice/vid traffic)class map important (match any)match (potentialy bandwidth hungry applications (http/ftp -...

merryllem by Level 1
  • 524 Views
  • 1 replies
  • 0 Helpful votes

I have just installed a CISCO 2801 router at a remote location with two T-1 lines (see config below)interface FastEthernet0/0 ip address 192.168.69.129 255.255.255.128 duplex auto speed auto!interface FastEthernet0/1 ip address 192.168.69.1 255.255.2...

dacruzer1 by Level 1
  • 677 Views
  • 2 replies
  • 0 Helpful votes

I have been reading all over trying to learn as much as I can about routing a single subnet in and out a single BGP peer but I am running out of time.We have a single 6500 with sup720 running BGP between 2 ISP peers. We advertise all out subnets to b...

I have a 2811 ISR running 12.4.11 T4 IOS and need to configure it for a 9 meg IMA.I can get all of the interfaces to work but not as a Full 9 Meg.Either as 2 - 4.5's or 1 - 6 and 1 - 3 MegIs there anyway to get them to work as 1 - 9 Meg IMA?2 - ATM/A...

I have two 1841 routers at two sites with a point to point T1 connecting them. They each have an Internet connection that the local site uses for their primary connectivity. I want to configure each router to use the other for backup in case their IS...

Resolved! Bridge or VLAN

Hi All,I'm very new to the Cisco environment and am attempting to configure a CISCO 1941 Router (IOS 15) to connect to a newly delivered ISP connection. I was expecting them to configure their device with Private IP addressing between them and me but...

accurisit by Level 1
  • 2685 Views
  • 9 replies
  • 0 Helpful votes

HI - I was wondering if there are any advantages or disadvantages to hardcoding the bandwidth statement on a MLPP interface versus letting it be set dynamically by the router.Thanks, Karen

kbehrens by Level 1
  • 1068 Views
  • 2 replies
  • 0 Helpful votes

Hello Guys, I have 2 routers with 2 T-1's connected with a crossover cable. I can't ping between routers. Why?R1controller t1 1/0framing esflinecoding b8zschannel-group 0 timeslot 1-24no shutserial1/0/:0ip address 10.30.1.1 255.255.255.0no shutR2cont...

Unanswered Topics