I have the following network topology:I need to configure routers R1 and R2 with EIGRP, and routers R2, R3 and R4 with static routing. All the end-devices must be able to ping each other.What I've done:The end-devices of R2, R3, and R4 can all ping t...
Hi there is a router connected to ISP. BGP in the router can allow all bgp routes in from ISP or none of them. What is benefit if we allow all bgp routes into the router from ISP? I know some of them. Anyone can mention all of them? Thanks
Hi All, I want to know what is this bug -CSCwc99652 related with as I cannot see the details of in in cisco bug website.Is this bug fixes by code 17.9.3 ? What is the severity of this bug,
I was trying to help out a friend's network which has a perculiar FlexVPN tunnels setup and have some questions, the scenarios as describe below: - A hub configured with 2 spokes which has some identical IP address as destination address in FlexVPN t...
Hi I am a newcomer who just moved to the network field.My Cisco router fan is bad and I'm trying to replace it, but I have a question.The model is the C2800 series. I want to know if the fan of the 2801 model and the fan of the 2811 model are compati...
Hi,We will be changing the route reflector server location from one site to another. Hence, I also need to move the loopback IP from one site to another. By doing this, I need to update all the clients (they all have peering with the RR loopback IP's...
Hello.It seems the 2 below devices are advertising each other making a routing loop.But the static route is advertising as tunneled. I don't understand why there should be any routing distinction for tunneled-- all devices need these routes tunneled ...
Hello.Quick question...If I want to delete an EIGRP redistributed static route from the network-- Must I locate the box in which the static route was configured and redistributed, then change that config,or can I execute a route deletion in any box i...
Hello WCCP Experts,I am running WCCP on CSR1000V on VMware. The HTTPS traffic is not being redirected.Interface IP-Address OK? Method Status ProtocolGigabitEthernet1 10.0.0.1 YES NVRAM up upGigabitEthernet2 10.34.198.1 YES NVRAM up upGigabitEthernet3...
I have two data centres and one of them connects upstream and receives the full internet routing table this is then forwarded via iBGP to the other Data-Centre (Don't worry about if this is good practice or not, it is configuration I have inherited a...
Hello, I am having a problem that BGP when it become down due to any physical issue didn't become up again due to NAT however i can't see any relation as there is no conflict in the Ips used in the ACL with the WAN ip used however when we added a s...
HISee diagram, so we want to set up another ipsec vpn on the network on the left which is our other DC, how could we set this up so if the 172.25.192.0/19 network wasnt available on the network on the right (DC1) then the routingwould dynamically poi...
Hi firstly apologies for this question I cannot get my head round the WAN stub site command. I get the stub router function, and benefits etc. But every time I read about wan stub site, it throws me and I dont get it. If its some sort of stub co...
Hi all,I am going through one of the CCIE BGP lab practices for route aggregation (CCIE Enterprise Infrastructure Foundation by Narbik). There is one particular lab (under BGP lab 6 task 4). Basically, it asked to configure R2 such that only R1 and R...
hi I have an ASR1001 pppoe server. If one customer have two connection and only one public ip, i must add static routers for give to customers router public ip for go to internet.exip route 31.188.188.188 255.255.255.255 10.10.10.12 10ip route 31.188...
