Routing

Hi,I have server (multicast source) which is connected to a switch port. The switch port is part of VLAN10. Other servers are part of VLAN 10 including a few receivers. IGMP snooping is configured on the switch. When the Source is on, I see that ever...

All,   I have a 10 mbps metro ethernet point to point link.  Nightly very large backups saturate the link, which is fine.  The issue is my network management traffic gets starved out and I get tons of device down emails.  The devices on each side are...

Hi,I have 7 numbers of 3750 Cisco Switch, they all are part of single stack. I found, there was flapping in the stack ports of Sw-3 (port-2) and Sw-4(port-1) which are directly connected with stack cable.I have replaced the stack cable with new one, ...

I want to use two static routes for my 3750's.  I have multiple VLANs on the 3750 and I just have a single /30 point to point connection to a 6513.I am adding a second /30 connection to a second 6513 which I only want to use if the first link is down...

I am having a issue with mpls label not getting assigned to vpnv4 routes. My lab setup is likeR6(CE) s1/3 ------à s1/3 R1 (PE) s1/2 -----------à s1/2 R3 (p) s1/3 ----------------à s1/3 R2 (p) s1/2-----à s1/1 R4 (PE) s1/2 --------à s1/2 R5 (CE).The v...

Hello,I have the following commands configured on my cisco2821 G0/0 interface:int g0/0ip adddress x.x.x.x x.x.x.xip helper-address 172.24.1.1ip helper-address 172.24.1.2speed 1000duplex fullno shut!Can I know how will this ip helper work? Will it alw...

Our 1721 redistributes into our 10.25.x.x WAN via RIP several static routes to hosts in an external 10.15.x.x network. However, there's another host in 10.15 that I need to access via a different gateway on another subnet that's directly connected to...

Dear team,               Iam getting continous alarma in my SONET links from my 7606 router.Jan  2 13:04:23.637: %SONET-4-ALARM:  POS3/2/0: B3-TCA declaredJan  2 13:04:33.645: %SONET-4-ALARM:  POS3/2/0: B3-TCA clearedJan  2 13:16:22.637: %SONET-4-ALA...

Question is how much bandwidth should we see with a 2811 and an IMA bundle pack (AIM-IMA and 2 dual port VWIC-2MFT-T1.  We are utilizing 3 t-1's in this scenario, so one should expect a 4.5 by 4.5.  But I though I read that the 2811 could only handle...

I am having a problem routing ip traffic with port numbers from one LAN to another. I have two networks 192.168 and 10.100.  I can successfully connect to devices from the 192 network to the 10 network and from the 10 network to the 192 network.  I a...

We are using a 836 router for connecting to the Internet via PPoE.I recently introduced in our LAN a Vista workstation. The user of this workstation cannot download large files e.g. from Yoursendit service.I switched the cisco router to the lousy fre...

Hi,We have three routers connected by serial link back to back. Router_A-->Router_B--->Router_C.Each router has fastethernet enabled. All routers are in same AS. We have BGP relationship established between Router_A and Router_Band Router_B and Route...