Yesterday I made a forum post regarding: https://community.cisco.com/t5/routing/cisco-1941-router-connecting-to-netgear-router/td-p/4700979The issue I'm facing now, Is that any devices connected to the Netgear Router (My PC) can't ping into the Cisco...
Forum Posts
Resolved! ROAS and using ethnet ports on a router
I'm currently running a ROAS config that goes up to some switch that is outside of my control. My ROAS works completely fine, however my cisco router has 4 ethernet ports that I'm trying to use but I can't seem to make them work. I tried setting up m...
Hi Tech People, I am facing inter vlan routing issue in my cisco 9600 (iOS 12.2). we can not use the gateway address in the device (see attached picture) my two Vlans (10,20) are in a same VRF and the device in VLAN10 wants to communicate with Server...
Hello, We see the following message in the logs continuously:%IOSXE-4-PLATFORM: R0/0: kernel: EDAC MC0: 1 CE INTERNAL ERROR on unknown memory (channel:0 csrow:0 page:0x2162fc offset:0x2162fc000 grain:0 syndrome:0xc1 - SBE) Can you tell me the meani...
I am having issues with Cisco 1000V routers getting lots of input errors. The error count below is from about 24 hours. There is OTV on this router, and the basic configuration is shown below. We have multiple CSR1000V's on this cluster, and the o...
Greetings All,I'm currenting working on a Cisco 9500-48Y4C 25 Gigabit switch with Amsterdam 17.3.1 IOS installed. We are using this switch so that our output source (custom FPGA through a 10 Gbe Core) can send out UDP data packets to our data capture...
HiI've been trying to connect my 897va router to my Virgin fibre by putting the Virgin Hub into modem mode.using the below config i get an IP address from the ISP but i can't get out to the internet so i assume it's a NAT issue or the ACL.I just can'...
Resolved! Adding three networks to one router
Suppose there is a new network called North that is to be added to the backbone. Given current devices, would that be feasible? If the answer is yes, explain how the current solution may be reconfigured to accommodate the change. If the answer is no,...
Hi, we are having tunnel from cisco lte router to asr at HO router. we have configured static Public IP at spoke router which is hosted by HUB router. the HUB is having route to this ip through tunnel and spoke is sending all the traffic to the hub....
Hi all, hope you can help me. I have system running where I want to use multicast. The system is a CCTV system and the network is as per below: Basically it's a ring running OSPF between Catalyst 9300 and the two catalyst 9300 to the right have Acce...
had the primary die, but secondary is up.I am fuzzy on the trick to get the active/secondary to replicate the config over to the new "blank" rma ASA.Best I recall isI need to copy all the interface commands over to the "new" blank asa.Something about...
I have an ISR 4451 with IOS XE 03.15.01c.S and IOS 15.5(2) when doing a "show version": 1. Which is more important to me? The IOS XE or the IOS? After reading several posts I'm not clear as to the difference. 2. Do I have Fuji, Denali, Everest or...
Hi,I've made a Network topology with a Class C IPv4 address (192.168.10.0) applying VLSM subnetting, and I got 8 LANs of 16 hosts (14 useful each) with the respective custom subnet mask (255.255.255.240) , when I try to make a connection with another...
Resolved! Non-transitive MED in BGP path selection
Hello, Please see below diagram. R4 send route 10.4.0.0 to R1 with MED 100. R1 can see the route with MED. MED is non transitive attribute. Why it happens? The diagram is from the link below. Thankshttps://www.cisco.com/c/en/us/support/docs/ip/border...
Hi Dears, I have a problem with the OTV tunnel site to site, for some reason I have packet loss from time to time, I don't see any errors or drops on the interfaces. SW-SITE1#ping 10.24.1.101 repeat 100Type escape sequence to abort.Sending 100, 100-b...
