have router ip 172.16.9.1 and my system ip in 172.16.8.1. i cannot access my router and other network of 172.16.x.x.only access router when my system ip 172.16.9.x. what configuration can make the router can access with all subnet of 172.16.x.x
have router ip 172.16.9.1 and my system ip in 172.16.8.1. i cannot access my router and other network of 172.16.x.x.only access router when my system ip 172.16.9.x. what configuration can make the router can access with all subnet of 172.16.x.x
I have a 2611 router connected with a dynamic ip assigned by the ISP. My configuration works fine for now but when I get a new ip assigned from my ISP I know my port forwarding will break. For some reason I cannot route-map to the interface fa0/0 i...
Hello,Please note, that I'm a newbie in Cisco networking. Just started with an ASA 5505 an can get quite well with it, except that I want to upgrade the ASA and the ASDM. I understand that the versions of the 2 are interconnected with each other.The ...
Hi,I've got my main campus dans a remote site connected with a GRE over IPsec tunnel in tunnel mode. The GRE/IPsec works just fine. My problem is with my outbound policy-map. This one is used to police the traffic to the Bw of the remote site. It got...
I have an issue at a remote site that when I run backups (on 1 server) that it brings the WAN to a grinding halt. I thought I would use QoS/Policy map to guarantee bandwidth for Citrix and printing but does not seem to be working. It appears that it'...
One of our ISP clients, needs to control their outgoing and incoming internet traffic accurately. Currently traffic upload (outgoing) is controlled by implementing PBR since this ISP doesn't receive any BGP Full Routing table from any upstream and th...
Hi,Just a quick question as I feel I am banging my head against a brick wall here: is it actually possible to redistribute eBGP into EIGRP? I'm getting external BGP routes advertised across our MPLS, and I really need to stick them into EIGRP. If it ...
Hi,Does someone know if it's possible to setup DSL interfaces to work "face to face" (like DTE to DCE with serial interfaces)?Thanks in advance.
I have an interesting scenario that I am working on putting together a solution for.I have a metro Ethernet network with only a Gigabit backbone connection between 2 locations. I need to give a customer a 145Mbps circuit using a gige handoff on both...
hi,Are they two different methods? I see that both of them use almost the same commands (interface tunnel, tunnel source, ...).The only difference I see is the Tunnel Mode and the IPv6 addresse we assign to the tunnel interfaces.any idea?
Hi,I am not able to telnet via vrf aware telnet service to ptp link having routes in vrf.There is an ACL on line VTY, and when i removed this ACL, telent success, but when i applied, it denies. Although all IPs are allowed on this ACL & matches are f...
All,Can you help? I am trying to provide backup to a remote site and the second line has been presented with a G.703 signaling on a RJ-45 interface. A few months back someone on here recommended a VWIC2-1MFT-G703 module. This module doesn't work with...
Just wanted to confirm if the NBAR Featureis supported withs72033-advipservicesk9_wan-mz.122-18.SXF15a.binImage
Hi,is loadsharing per packet supported on the ISR routers?What commands can I use to influence Loadsharing on the ISR routers?Thanks and best regards,Peer
What is the easiest way of putting an IP on my 4948s so that I can manage them over the network remotely. Here's my setup:Switch A - 6509, vtp server, contains all vlan interfaces for all vlans.Switch B - 4948, vtp client, trunked to switch A and Swi...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-28-2025 01:50 AM | ||
05-27-2025 05:13 PM | ||
05-15-2025 07:28 AM | ||
05-13-2025 03:49 AM | ||
05-12-2025 03:28 PM |
User | Count |
---|---|
5 | |
3 | |
2 | |
2 | |
2 |