Hi,In ospf, I config the passve-interfce to interface. e.g.router ospf 1network 192.168.1.0 0.0.0.255passive-interface fe0/0Does it mean that the interface FE 0/0 MUST be the "stub area"?ordoes the "passive-interface" appear in stub area? If config t...
Hi,Is it possible to configure the HSRP between Cisco 2651XM and Cisco 2651 routers?Is it necessary to have the same IOS version in both routers?Please help me.Thanks and Regards,S.Venkataraman.
guys few ospf question if some can please advise:area XX stub no summaryarea XX nssaarea XX nssa defaukt information originatearea xx nssa no summarywhat does the above commands do secondly ospf over NBMA.....if we put the command on interface ip osp...
Here I am a-studying multicasting for my BSCI exam.With RPF, the router looks at an incoming multicast-destined packet and examines its source IP address. If the router has a route to that source that goes out via the same interface the packet arriv...
adding WIC1DSU-T1 TO 1721...PURCHASED NEW CARD WIC1DSU-T1 v2...ROUTER WILL NOT RECOGNIZE NEW CARD USING SETUP. HAVE TRIED 2 DIFFERENT FUNCTIONAL ROUTERS.
Hi,How do I config eigrp to advertise the "default route" to nei? any sample config?rdgs
I just encountered a new command that I've never seen before. Does anyone know the proper use of the interface command "pulse-time.'I see it in the command reference. But it doesn't say much.http://www.cisco.com/en/US/docs/ios/12_2/interface/command/...
Hey there,Sorry. I've been reading and reading but I guess I'm doing an uncommon scenario.I have a slow (256k) wan link. I need to push all WAN users aside when I dial in with my VPN client to do maint. Can anyone give me some QoS options?The other Q...
Dear Friends,I am using Switch 3750 of upgrading its software but accidently i format FLASH filesystem that make my switch unusable. Can anybody tell me how to solve this problem. It's seem now that i am not able to use the Switch.ThanksFaisal Mubar...
One servers ip is 172.16.5.x this is connected through one path (path1) and secondary ip is 10.10.2.x through another path(path2)Want to communicate to secondary ip as primary ip through path2.1. LAN - Router1- Router - LAN-Server (172.16.5.x)2. LAN ...
Hi, all, I've a little problem.I configured my 871 to take IP address from the WAN interface, a D-link modem.The modem send via DHCP the information that the router needs to operate....all still works, but, I've this error in the log:Looping packet d...
Hi,I config the 6to4, the config is:R1interface loopback 0ip address 172.16.20.1 255.255.255.255interface tunnel64 ip 192.168.1.1 255.255.255.252 tunel source loopback0 tunnel source ipv6ip 6to4is it invalid config? if yes, what is the source ip addr...
Folks, on my router I am trying to copy a half-page of text and then paste after doing #banner motd lineHowever, once I paste the text I get output saying "command was not identified". Can you pleae explain how can I copy large text from notepad and ...
Need assistance in solving thisparticular issue and would greatly appretiate your help.Nothing is broken but instead need to learn what obtions I have in following situation, not strong on bgp.Couple of months ago we migrated all of our sites from PR...
Hello everyone,I have been busy for a few day to try to set up the NAT with asa5505.Please see the attachtment for the configuration of the modem and the asa. Hopefully someone can help me out. Thanks in advance. Peter
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 05-20-2025 11:22 AM | ||
| 05-19-2025 12:25 PM | ||
| 05-15-2025 07:28 AM | ||
| 05-13-2025 03:49 AM | ||
| 05-12-2025 03:28 PM |
| User | Count |
|---|---|
| 4 | |
| 2 | |
| 2 | |
| 2 | |
| 2 |
