Good evening everybody . I have some strange problem with PBR setup on 3825 . Here is the part of the config :interface GigabitEthernet0/0.X encapsulation dot1Q X ip address x.x.x.x ip flow ingress ip flow egress ip nat inside ip virtual-reassembly z...
Hi there,I'm investigating an issue involving NAT and I'm unsure what gets translated to what based on the following config (from Cisco IOS NAT on a 6500 switch). I was under the impression that NAT used standard access lists but this one's an exten...
Hello Cisco Networkers..I have a pretty cool question.I am by far not considered a expert in BGP but here is the question.If you have a eBGP relationship between 2 ISP providers, both peers in the relationship should pass the FIRST (FULL INTERNET ROU...
Ok,I posted a couple of days ago about a telnet problem that I had where I could ping the router, but couldn't telnet to it. There are NO acls involved at all.Well today, I figured out that I can telnet to the router from another router, but not from...
Hi,What would ^550*$ mean? I''m getting myself confused - I want to say permit anything originating from AS number 55001 to 55099.Any help would be much appreciated!Thanks,J
In the serial interface we have applied the following Qos:!Interface serial 0/0random-detect dscp-basedservice-policy output WAN-SERIAL!policy-map WAN-SERIAL class class-default shape average 487000 service-policy WAN-OUT!Policy-map WAN-OUTclass...
Hi,Can anybody assist me how to migrate from EIGRP to OSPF while in production environment in order to avoid any outage.Best Regards,Rahim Amir Ali
I know we can conditionally not advertise routes if a certain route/s are not in the BGP table, but I'm not sure how to stop advertising the entire BGP table (if we are providing a full routing table to a customer) if a route or routes are missing fr...
hi, i have configured easyvpn server on ASA 5550 and installed vpn client on remote systems. It works fine on every system except one system in which the status shows encrypted 0 decrypted 0 packets and discarded every other packet what is the probl...
Hi,i have 2 routers connected to the internet (live ip on ethernet interface)they both have different service providers hence diff ip pools..i need to connect them so the LAN on each side can access the other LAN .10.0.0.1(Router1)202.x.x.x INTERNET ...
I have a problem with my 2811 CISCO.After I just finish configure this I received message from attachament.Can you help me?
Hi Experts,I would like to know if there is any softwares/tools (which is free) that can do a one goal updates from the remote end so that we don't need to do from one switch to another switch?Thanks.cindy
From yesterday night, lots of error informations appear in cisco 7506 and errors pop all the time until now. %OSPF-5-ADJCHG: Process 1, Nbr x.x.x.x on GigabitEthernet3/48 from LOADING to FULL, Loading Done %SYS-3-CPUHOG: Task is running for (2680)mse...
Hi Gurus, Will route-map and prefix-list command work together on bgp ? i tried using filter-list and route-map they work properly. This is on outgoing. tia.
Between 2 cities I have 2 connections, 4 routers, and 2 ASA5510s.Louisville has a 2851 that talks to a 2821 in Lexington over a MPLS line.Louisville has a 3662 that talks to a 3640 in Lexington over a Point-To-Point connection.I want to use the MPLS ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 09-12-2025 09:12 AM | ||
| 09-05-2025 07:37 AM | ||
| 06-14-2025 01:24 AM | ||
| 05-12-2025 03:28 PM | ||
| 05-09-2025 02:25 PM |
| User | Count |
|---|---|
| 14 | |
| 6 | |
| 3 | |
| 3 | |
| 2 |
