Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

Resolved! ATM over PPP

I have configured the below configuration in Cisco 1821 router interface ATM0/0/0 description : ADSL Link to ISP no ip address no ip mroute-cache no atm ilmi-keepalive dsl operating-mode auto pvc 8/35 ----------------- ( i got this information fr...

All,I am starting to work on a major MPLS deployment.We selected 2821 and 3825 as CE for frame & T1,T3.<< Verizon advise>>. Should we better stick to 3845 for future traffice growth<<throughput,x-mission,etc>>.Also, any ""good"" link on best practice...

What would be the proper syntax for a route-map to do the following for routes received from a specific bgp peer:1. accept all routes *except* default2. set the local-preference to a non-standard value.

lowen by Level 1
  • 578 Views
  • 1 replies
  • 0 Helpful votes

HiCan anyone tell me what Cisco means when then said "Double ACL scenario".Does they means that the packet pass in the standard ACL and then pass in the CBAC dynamic ACL ?Thank you very much for your help p.s. It's regarding a possible related bug o...

2 mpls wan link , getting terminated on 2 different routers. each router connected to a single 6509 siwtch. so router A---6509 A and router B ---6509 B6509 A --- 6509 B --HSRPthe routers A and B are going to exchange routes with providers routers run...

Hi, I have a quarry on accessing router (broad band) through internet. Can we shut the router LAN and WAN interfaces by accessing the router through internet? Regards,satya.M

guys one way of controlling routes is using a distribute list. now i have abasic question abt distribute list.when we use distribute list we can use it with prefix-list or access-list is it same or both has got some different purpose for examplewhat...

Resolved! BGP Peering

Hey,I have a question for all the network professionals out ther..I am working on a big project..Basically, I work for an ISP.I have 2 7609 routers connecting to 2 Gateway Service Routers (GSR).My question is.. These GSR act as a Gateway, interacting...

Mavrick25 by Level 1
  • 1637 Views
  • 7 replies
  • 0 Helpful votes

I have a 7300 router I need to add another T3 card...Can I just plug in the card without powering down the router, or must I power the router off first then install the card?Greatly appreciate the help..thanks!

ud0508500 by Level 1
  • 524 Views
  • 2 replies
  • 0 Helpful votes

How to whitelist IP's if the service provider is Blacklisted, the result of this is undeliverable mails as they are getting bounced back. While some specify the reason, others say PTR records missing. Pls suggestThanks in Advance

Hi,Attached is the network diagram and Pix Configuration. We have data circuits for all our branches just installed. The problem is that the Pix just stops to ping the branch Office routers.1. From the Pix can ping 192.168.1.2 & 1.32. From 192.168.1....

Hello guys,I have a 2821 router that I need to upgrade. I want to copy new IOS from TFTP on my computer which I am doing all the time. I have enough flash space I have connection to the TFTP server but I am getting this:Accessing tftp://192.168.x.x/c...

rvr_76bg by Level 1
  • 927 Views
  • 4 replies
  • 0 Helpful votes

Hi guys, I have a problem.I know interface aggregation works when the interfaces you are aggregating are going to same device.Is it feasible to create an aggregate interface when interfaces are connected to different devices.Lets say I have 3 ...

mallu by Level 1
  • 1006 Views
  • 2 replies
  • 0 Helpful votes

HiI am confused of what serial ports to buy for 2620XM. In this link in figure 4 there is a network module that has 8 serial ports. But they are asynchronous/synchronous serial ports?The link is:http://www.cisco.com/en/US/prod/collateral/routers/ps27...

omal by Level 1
  • 2182 Views
  • 6 replies
  • 0 Helpful votes