Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

Hi, Customer wants to use 2 independent networks termiated on one common switch and wants to use the networks based on time. We can have time based ACL but customer wants to have time based port shutdown and no shutdown to get more security.Please, l...

jachowda by Level 1
  • 19256 Views
  • 5 replies
  • 0 Helpful votes

Just been going through QoS and labbing a few things and have come up with a problem.When QoS is configured on a service provider ethernet link for instance a 4Mbps symmetric, queuing doesn't seem to work correctly in that most of the congestion cont...

dataylor by Level 1
  • 487 Views
  • 1 replies
  • 0 Helpful votes

Hi,My 2811 power supply stuck in "in use" status after a power supply failure.When I put again the 2811 power supply, the supply stay provided by the RPS2300.#sh environmentMain Power Supply is ACRedundant Power Supply is attachedRPS status: in useFa...

ogor by Level 1
  • 702 Views
  • 1 replies
  • 0 Helpful votes

Resolved! EIGRP vs OSPF

As i have read until now (monstly through cisco books, CCNA and CCNP) those prodocols are those that are suggested for using in your network. I use EIGRP in my network since all my devices are Cisco(also the switches). My network has now around 50 no...

I had always thought the BGP path selection algorithm whittles down the alternative paths by elimination until only one candidate remains. But according to Wendell Odom's CCIE Certification Guide, page 445, that is not so. It appears that each of t...

I have version 7.2(1) on asa 5510. Due to reverse route putting a static route on my routing table. When the tunnel goes away shouldn't the static route go away also?

rlloveras by Level 1
  • 754 Views
  • 2 replies
  • 0 Helpful votes

Has anyone tried configuring 2 RR's of same cluster as clients to each other.Logically it should work as reflected routes from 1 RR to other RR will have cluster Id attached hence the peer RR will not accept the route.Any suggestion???

tahseen12 by Level 1
  • 447 Views
  • 1 replies
  • 0 Helpful votes

Hi all,We have links to two differnt ISPs. We recieve partial routing entries and default from both, however only one default route appears in the routing table. This is a problem for us as large amounts of traffic are still using the default route, ...

jigsaw2026 by Level 1
  • 6039 Views
  • 13 replies
  • 0 Helpful votes

I get an error %USB_HOST_STACK-3-USB_FLASH_READY_TEST_FAILED : USB flash failed to pass 'Ready' test when I connect a 2gig usb drive to a router with version 12.4(11)T4.Can anyone suggest any remedy?

Hi all I have cisco 1841 router with hwic-2shdsl card. IOS c1841-advipservicesk9-mz.124-15.T3.binI need to connect Zyxel IES-1000+SAM1008 in mode 4wired.Config on Cisco:controller SHDSL 0/0/0 dsl-group 0 pairs 0, 1 shdsl annex B shdsl rate autoCon...

georgd by Level 1
  • 1406 Views
  • 5 replies
  • 0 Helpful votes

Resolved! OSPF problem

Hello,I have recently started in networking department in my company. I am attaching 2 txt files, one with sh run output , second with sh ip route output. Interfaces s0/0/0 and s0/1/0 are connected to 2xT1 to the other site of the company. The config...

rvr_76bg by Level 1
  • 1339 Views
  • 9 replies
  • 0 Helpful votes

Hi,I have a Firewall,whose Outside interface is connected to a ISP with a Public IP address,now I want to protect this Outside interface.How can I do this?Basically it is like a Hardening the Firewall or a Router which is directly exposed to global n...

Lavanholy by Level 1
  • 758 Views
  • 4 replies
  • 0 Helpful votes