We have Unity deployed in 6 sites. One site reports that voice mail only,is garbled. I have located a few documents referring to this issue, but no clear resolution. Any thoughts?
Hi all,Just received a consignement of Cisco 815 routers and I cannot make them to lock to my CMTS downstream. My CMTS uses 6MHz band (like the North Americans), downstream freq 579MHz and 585Mhz and based on DOCSIS 1.0I will be very grateful for any...
Hai all,Sorry to ask very basic quiestin ...how implement natting in LAB ..if i ve two router in labs how can i perform the same ...it wud be better if some one cud pase the config Pls forgive if this is rubbish quistionThanks in advanceLijesh.N.c
Hello, IS-IS DIS sends hellos at 3.3 seconds, so does it means 3.3 seconds between DIS and all other routers as well as other routers also send hellos to DIS at the same seconds... and IS-IS normall routers are exchanging hellos between them at 10 se...
Hello.I have a Cisco 837 and wondered if the DSL FW can be upgraded like the 877's can? Here's it's output.Router#sh dsl int atm0 ATU-R (DS) ATU-C (US)Modem Status: Showtime (DMTDSL_SHOWTIME)DSL Mode: IT...
I'm seeing underruns. Unfortunately, searches on what causes this exactly tend to turn up people's show controller commands that have 0 errors.M1T-T3 pa: show controller:PAS unit 0, subunit 0, f/w version 3-93, rev ID 0x2800001, version 3idb = 0x200...
Hi,We have recently had a 50Mb ethernet service provisioned between 2 POPS - Latency is approx. 13m/sec.Testing the service, we are only able to achieve ~800K/sec (FTP+HTTP between 2 Linux boxes) in a single session(If we run multiple tests simultane...
A few times a day we can not reach one subnet across one of our WAN links. the traceroutes die at our WAN router before it hits our core router. I cleared the arp table on the 2651XM WAn router and was able to ping. I am not sure if it was by chance ...
Good day I just have a quick question...I have a point to poing frame relay connection and I want to enable fast switching at the distant end. If I do that is there a possibitlity of disconnecting myself from the distant router? Also would I need t...
Hi,I have this setup as attached. I'm thinking if this will work and wondering if the reason that I can't connect to Internet from LAN is because the IP addresses that I assigned to the ADSL modem and the router are private addresses. ASA5505 is dire...
Hello,Whether the EIGRP topology table will have details of all the links in the network? or only details of links connected to its neighbours?In many documents,it is given that ,eigrp topology table will not have all the links in the netwok/AS liste...
I have been asked to make a list of all of the switches and if the ports along with VLAN's are forwarding or blocking. I have been trying the CNA and feel that the information I need is there but I just haven't been able to view it. Any ideas?Thanx,M...
Hi,This is basically a call center setup where all external voice connections will get terminated into edge switches.We need to run iBGP between ASA5540-AIPSSM, 6500 switch having FWSM modules. eBGP will run b/w ISP & the Internet Routers, rest will ...
hi dudes!I have two GSRs as Internet routers in my network which I am intended to connect with two ISPs. I want to have in each router two links directly connected with both providers for BGP redundancy purposes, but due to economical limitations a s...
Hi everyone,I have the question about how the packets that match the access-list and match NAT statement are switched on CEF enabled IOS router. Router is Cisco 7301, Cisco 3825 and Cisco 2811 and all of interfaces are CEF enabled.The access-list doe...
