Routing

Dear all,I have a Cisco 871 router called 'ROUTER871'. It is providing Internet and VPN service through a 1M leased line. The Cisco 871 is suppose to replace an aging Fortinet firewall. Current Internet traffic is normal http, https, ftp and dns. The...

I knw that Multi-framre relay allows you to bundle multiple E1's or T1's on one link. I wanted to know can I have a mix of E1's and T1's in a bundle or is it that I can have only either T1's or E1's in a bundle. Also what is the maximum number of l...

I recently replaced a Cisco 3640 Router with a new Cisco 3825 Router. We use multiple T-1 Circuits (IMA) for WAN connectivity.The partial configuration for the ATM setup is as follows:interface ATM1/0 description ATM CIR 1 no ip address atm vc-per-v...

Hi,May i know how you guys will setup the multicast for 2 pair of 6500s core switches?Currently for my case is that each pair is connected with a trunk (layer 2) running HSRP to provide redundancy, then these 2 pairs are inter-connected (layer 3) tog...

We have a 2811 with 4 Vlans. I want to put a ISA 2006 server in one of the vlans and have it perform reverse proxy to our web server on the Lan. Do I need NAT or can I pass this through with a Access-List

hi guys, Need your help. OSM-4GE-WAN-GBIC module of cisco 6509 switch got reloaded, while rebooting it gave the lcp failed to go online error and card did not came online.after jack out jack in it came up. now it is working fine for last 24 hours. Ne...

I have 2 routers-R1 ( L0=172.22.23.1) and R2 connected to each other in 2 ways - PLC Link 1 and via MPLS IP VPN.#sh ip bgp* 172.22.23.1/32 172.30.0.54 0 3216 65334 i*> 172.22.22.17 ...

hi guysi have a 6509 with sup2when i want a copy a file from bootfalash: into sup-slot0: after a while the system crashes! and will reload!any hint?

Hi All,I would like to configure both radius & tacacs authentications on Cisco 7600 router.Is it possible? Can anyone give me some tips or refer to some urls?Thanks,Beno

I have inherited a nightmare and need to know if what I am trying to do is possible with what we have (2811 with Advanced Security 12.4). I have 2 sites connected via 2 point to point T1s, connected through 2 port HWIC in each router. Each site has...

hi,i have this configuration:!interface FastEthernet3/0 ip address 10.0.0.1 255.255.255.0 ip nat inside ip tcp adjust-mss 1452 duplex auto speed auto pppoe enable pppoe-client dial-pool-number 6 pppoe-client dial-pool-number 5 pppoe-client dial-pool-...

Dear guyswe have a 6509 core switch in our datacenter.this 6509 includes two supII.these two SUP II has same problemtheir RP will crash but their SP work fine.when I boot the swtich from the my disk (IOS Software) after few seconds the system softwar...

3. The following line is taken from the output of the debug frame-relay lmi command:1w2d: PVC IE 0x7, length 0x6, dlci 100, status 0x2, bw 0 What does the dlci 100 status 0x2 indicate?

I am not an expert of routers, our business has a T1 line and a DSL line from different ISP. Our current configuration is Mac users use one of them, and PC users use the other. Since none of the internet service is stable enough for our need. Once a...