A genaeral question in designing a solution as above...My preferred solution for small office connections used to be an ASA5505 front ended by an 800 series router. this was fine with 100Mb ports and WAN data rates of about 80Mbs. Obviously that solu...
Hi All,Forgive me if this is a stupid question. I am very new to networking and in the beginning stages of setting up my home lab for learning the CCNA. I have acquired 3 2811 routers and 4 catalyst 3550 switches. I am trying to set them up in the sa...
I have ASR and want to configure is as VPN server=Device:=cisco ASR1002-X (2RU-X) processor (revision 2KP) with 3746359K/6147K bytes of memory.Processor board ID FOX2449P4F0=IOS:=Cisco IOS XE Software, Version 17.05.01aCisco IOS Software [Bengaluru],...
Hi, Routers have higher OSPF AD value(210) by using distance command under OSPF.And they have IBGP peering and they are redistributing OSPF routes to IBGP(AD 200)I see they keep routes learned from OSPF(AD 210) even if the IBGP AD(200) is lower AD 21...
HiWe have a pair of Nexus 5k in VPC domain and these connect to a x2 stack switch through a vPC, the stack switch is already runnig BGP where we peer with ISPif I were to configure BGP Between nexus 1 & 2 and Stack Switch would I use ibgp or ebgp ??...
BGP-100 (Issue pinging from R5 to R1(customer) via R3) The router in Intra area not able to communicate with Customer Vrf(Router-1) . Router 5 has Customer routes on its vrf table, but unable to communicate. Router 3 directly connected to Customer VR...
I'm trying to configure my ISR4331 with BVI but I don't have an option for ieee so I'm stuck and unable to create vlans
I have a test environment. I have 4 ospf areas "Area 0 backbone , Area 1 normal , Area 2 NSSA and Area 3 Totally NSSA." Inside the Area 2 I redistributed EIGRP 20 and Area 3 i redistributed RIP. I have one more network EIGRP-1which is connected with ...
Hi,Although I've managed to set up an 837 router to do what I need (VPN/NAT/PAT), I'm a bit confused by the interfaces. My understanding is that the layer 1 settings such as speed / duplex are done on the fastethernet 1-4 interfaces, and the layer 3 ...
Hello, I need help with my final project for my Switching, Routing, and Wireless class. My hosts are not receiving the correct IPv4 address, and they haven't received an IPv6 address at all. I'm doing the project on packet tracer before I move onto t...
Strange situation appears to be network related so far. Hoping an expert can assist me.My environment:Satellite office (CISCO router 2851 / cisco sw c3750) ----------COMCAST EPL (FIBER)-------MAIN SITE (Cisco ROUTER 2851/Cisco 3750 switches Stacked/...
So I always had hard time understand NAT, but this is weird. How I imagine there shouldn't be any difference from which VLAN I try to connect, but the "Public" Vlan 10 successfully reaches webserver, while "Admin" Vlan 20 does not. Any help?Building...
I HAVE THIS 192.168.11.1 IN A SWITCH L3THE PORT IS NO LONGER ROUTEDAND STILL FOLLOWS THE PROBLEMAND IF I TURN IT OFFCONFIGURED SVI IS OFFA PROBLEM THAT I DO NOT UNDERSTAND WHYI WANT TO DELETE THIS NETWORKANOTHER THING AND I SEARCH WITH THE SH RUNNING...
Can anybody help me to understand why BGP flapped if there is no issue in ISP media. ==================================BFL_BURHANPUR_TCL#sh verCisco IOS Software, C800 Software (C800-UNIVERSALK9-M), Version 15.5(3)M4a, RELEASE SOFTWARE (fc1)Technical...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 10:40 AM | ||
07-15-2024 05:07 AM | ||
07-13-2024 09:04 AM | ||
07-09-2024 05:41 AM | ||
07-03-2024 08:54 PM |
User | Count |
---|---|
14 | |
12 | |
8 | |
6 | |
4 |