HelloIts my first time to upgrade 6500 multilayer switches. My big question is what i pay attention for upgrading this devices. The switches serve sverals modules. I will upgrade to s72033-adventerprisek9_wan-mz.122-18.SXF10.bin currently:s72033-adv...
i can't get isdn connectivity in 1841, but same isdn connection working in 2600 series
Hi all,I am configuring a cisco switch 500 series and all access ports will be set as cisco-desktop smart port.This switch will be connected to a 3com switch via uplink, vlan1. Which smart port should I use? Can I also use cisco-desktop?
Greetings,I'm rereading my materials for CCNA, and I can't quite fully understand when does which timer start counting down on these protocols.. My searches for this topic always came up only with their values&light descriptions. Could anybody please...
Hello,Can i have a quick briefing on any carrier-class centralized management/configuration system, that automates the configuration process for MPLS L3, L2VPNs, VPLS, IPTV, VoIP, gaming ... etcI read about the SCE but it doesn't seem to help on the ...
I'm confused with those!if i have R1 and ISP routers, ISP connects to the internet cloud and R1 connects to it(what is connected to R1 is or a lan or another set of routers)so given this topology - when do i choose static route,default route or stati...
Hello, I have a very basic question. Needs your input. If i want to send Static route into OSPF environment. Then which of the following options would work. Unfortunately i cannot test it..so wondering if someone has tested this environment can...
I have 2 DS3's from point A to point B with both circuits in the same router at both ends. I have CEF enabled and I have the "ip load-sharing per-packet" statement on the interfaces but all of the traffic is only using one circuit. If I do a "show IP...
Folks,I cannot access this box at all. HyperTerminal shows nothing, I have tried to reset defaults, and still nothing. Defaults to 10.0.0.1? I should then be able to access from browser? I have hyperterminal setup correctly. I am stumped, any id...
Dear I need to run my IPS through network i configured my sitch 3560 but when i entered this command : monitor session 1 destination interface Fa0/24 i lost the connection with IPS.i put the monitoring IPS port at SW port/24 .... what is the problem?
i can't get isdn connectivity in 1841 , but same isdn connection working 2600 series
Hi,When looking for an IOS for a router, how many bugs are considered to be too buggy? How do you determine which IOS to pick?Thanks,Yolande
I don't understand why Split Horizon rules will cause problems on NBMA networks such as Frame-Relay Hub-and-Spoke for example.(?)
I want to create a user on my 1720 so other IT people can log in but have limited privileges. All I really want them to be able to do is see the output of a 'sh int Sx/x' or 'sh service-module' to see if a T1 circuit is down. I have an encrypted se...
Hi Guys,I know that this belongs in the wireless forums but I didn't receive any responses over there so I thought that I'd try my luck here.I'm looking for some insight on the procedures to connect 2 separate networks using 1300 series bridges. The ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 10-26-2025 02:24 AM | ||
| 10-24-2025 11:24 AM | ||
| 10-16-2025 11:52 AM | ||
| 10-15-2025 06:33 PM | ||
| 10-15-2025 04:37 PM |
| User | Count |
|---|---|
| 5 | |
| 4 | |
| 1 | |
| 1 | |
| 1 |
