Dear sir,Iam attaching one word file plz go through that and any budy suggest good solution and bill of material.regardssrinivas.D9246571397
Dear sir,Iam attaching one word file plz go through that and any budy suggest good solution and bill of material.regardssrinivas.D9246571397
Hi,Im new to IS-IS, and Im trying to work out how IS-IS routes get into the routing table? I read that IS-IS is working at layer 2. I am following the cisco press BSCI exam certifcation guide, but I must be missing a command or something because my...
what is difference between "ospf auto-cost reference-bandwidth" and "auto cost reference-bandwidth" syntex?
Dear sir, Pls send me the command of telnet asscess and ssh access for global access firewall is Csico 501 Regards srinivas.D
i have bri connectivity which is configured using dialer. the configuration is given below. according to the configuration second bri channel should go up when there more data transfer. that is working fine. the problem is when ther is less data tran...
2811 router with SDM.The bandwidth usage (monitor, interface) for an interface in SDM is reported as a percentage, but of what? The interface is a FastEthernet, but it's set at speed 10, duplex full.
Ok the story so far.Started off with 2 routers behind a firewall. The firewall separates them from the 192.168.1.0 local LAN.Both routers have external internet ip addresses on their LAN and WAN interfaces.One router is for internet access. all host...
I have 7606 which is using 12.2(33)SRA2. I have configure the router using our standard config. However when we config for the router to use last resort password when tacacs is not avail, its not working. The router accept the command. But the...
Hi all,Just wondering if setting the bandwidth on ATM interfaces on a Cisco router is important? We have T1 circuits running ATM back to our main site. Right now the routers think the interfaces are capable of 25Mbps.Thanks!
Is BGP not included in all IOS images I just bought a new 2811 router and it says bgp is not in this image.
Imagine I have devices which muticasts and broadcasts tons of UDP traffic on a given network. Suggested solution is that I should put a router and let the device on the respective network (10.0.0.0/8) installed there. Note that the respective devices...
I have one Cisco 7206VXR (NPE-G1) with IOS version 12.3(17b) and using QoS Priority Queueing on Multilink PPP interface.The ACL number 100 doesn?t have match, then, the QoS isn?t operating.Do you have idea the issue? Will be IOS bug or configuration?...
I have a 3660 router and need to upgrade the IOS. The new version is 29 Mb large and I have only two pcmcia flash memories with 16 Mb each. My question is: "Is it possible to use them as one only?" Attached is the show version with actual information...
Hi there...Is there somewhere I can go to determine which routers I will need to replace the ones that are no longer supported (i.e. 3600 series routers)
I need to secure the Ethernet interface to allow ONLY my device access, as it is open to the public. How do I do this ?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted | 
|---|---|---|
| 10-26-2025 02:24 AM | ||
| 10-24-2025 11:24 AM | ||
| 10-16-2025 11:52 AM | ||
| 10-15-2025 06:33 PM | ||
| 10-15-2025 04:37 PM | 
| User | Count | 
|---|---|
| 5 | |
| 4 | |
| 1 | |
| 1 | |
| 1 |