Hi,I need to configure this onto the console port of the 7200 router. I put it on the AUX port but I need to put it onto the console port.Is there a document that explains how to do thi?
Hi,We are having a setup something like this:PC=>2950=>2620=>7200=>NAS boxUsers are having intermittent slow response access files on the server. It is only file access which is slow. Apart from this, everything else seems to be normal.Do anyone has ...
I received tons of this message.%PIM-6-INVALID_RP_JOIN: Received (*,224.0.1.40) Join from0.0.0.0 for invalid RP 10.0.1.1How do I know which device is sending this if it is showing 0.0.0.0?Also, I don't have "ip pim accept-rp" command on this router.P...
I have an IPSEC between a pix 506 and an ASA5510. The tunnel is over DSL links and there is a problem with traffic not going through correctly. Initially I was trying to get a server remotely to join the domain across the VPN but this was timing out...
Dear,I've recently installed a new 2821 router to replace an SMC ADSL modem. Since then, the lan cannot browse some websites, e.g. http://www.isabel.be, http://www.msn.com, http://www.sapo.pt.Other websites work fine. There are no restrictions yet on...
Hi!i have a couple of questions!1)if we have 4 link, the first 3 is gig and the 4 one running on the gig interface, but the actual speed is 300M?2)can i run Multilink bundle on this 4 Links(1 of the 4 in different speed 300M But running on the gig in...
what's the significance of seq number in route-map command say for ex there are two route-maps with same name with different seq num the one whcih has the less seq num will be given prefernce?
I'm trying to setup a GRE tunnel to share EIGRP route across a linux firewall. I found a document on using IPSec with GRE across a firewall to distribute EIGRP:http://www.cisco.com/en/US/tech/tk583/tk372/technologies_configuration_example09186a00800...
I'm having a problem with our 6509 switch. We have had RIP enabled for a while and we'd like to disable it on this switch because we felt that it was not being used. However when RIP is disabled, after a short period of time, it appears that the 65...
Hi,I have a strange situation that I am hoping someone can shed some light onI am putting a WAN in place for 50 sites in the UK where all the branch locations have a ADSL Tail into an MPLS Cloud and a ISDN 2 backup that dials into the HQ. The HQ has...
According to Cisco documentation, a crc on a serial interface is conducting a crc check at the packet level. I have also seen documentation that says that crc's are performed on frames, a crc check is used to decide if an fcs should be incremented....
I configured some NAT port forwarding through SDM(as a newbie) but none of them worked for me. For example, I have a web server behind the router, so I setup a IP forwarding from my external static IP to the web server's internal IP 192.168.1.xxx thr...
HiI want to chk the same call failur on my As 5300 how can i trace it through the debuger option and how can i collect the trace ???and when debuger is on wht about the call which are active willl there b effect on te calls ???thanks
I've searched the WAN forum and didn't find anything that specifically answered my question so here goes:I've got a 3745 with 512 MB and I'd like to now receive full routes from both of my providers. Currently we are receiving only a handful of local...
Hi, I got a 877W router and I forgot the password to get into the system so I used the confreg 0x142 to reset the router to factory config.But now I can't connect to the router through SDM because it lost the default LAN config of 10.10.10.1.Is there...
