Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

hi I have a few routers in a lab and have async connections to their con 0 port for a 3745 with an 8 port async card.the config in the lines and con 0's is as documented on CCO.When i am telnetted thru the 3745 onto the con 0's I keep getting spuriou...

Currently I have 2 DS3's to two different providers (ATT & Broadwing). I am turning up a third circuit which is an OC-3 to ATT (AS 7018). Right now I am using AS-Prepending on my /24's to successfully balance inbound traffic on the two DS3's. However...

jradke by Level 1
  • 569 Views
  • 3 replies
  • 0 Helpful votes

Here is my config.interface GigabitEthernet1/0/1 description RECORDING_SERVER switchport access vlan 110 switchport mode access spanning-tree portfastmonitor session 1 source vlan 110 - 121monitor session 1 destination interface Gi1/0/1 ingress untag...

HiI am trying to setup two 877 routers so that they talk to each other over GRE/IPSEC . However I need to be able to set my ATM0.1 (Dialer0) to static rather that assigned so that I can then setup the tunnel. However whenever I try to add the Public ...

openipltd by Level 1
  • 2126 Views
  • 2 replies
  • 0 Helpful votes

I've got an 1841 with two separate Internet connections via separate ISP's, one using fe0/1 and the other using ser0/0/0. fe0/1 currently provides all Internet including two L2L VPN's and all general Internet via NAT overload using fe0/1 IP. With s...

Hi,I'm running Solarwinds Real-Time Interface Monitor, in which I am monitoring one of my remote routers, which is a 2691 VPN bundled device. I'm troubleshooting high latency issues which is hurting my site to site Microsoft exchange connector. Suppo...

jkrawczyk by Level 1
  • 465 Views
  • 2 replies
  • 0 Helpful votes

Hi for all,I've a router Cisco 2801 and the service from the provider is Digital Leased Line (i.e. D.L.L) and another router (Cisco 2801) has a DSL.So, what are the interfaces that going to attach with two routers.Note: the purpose for these scenario...

My question is simple, will a Cisco 1841 router support 2 T1s sustained? Cisco's tests were based on multiple services (QoS, ACLs, IPSec etc)running to determine it's rating of supporting 1 T1 sustained, but I need to know can it handle 2 T1s running...

sgray by Level 1
  • 709 Views
  • 3 replies
  • 0 Helpful votes

Hello All,My company has acquired a smaller company that has a Fios connection and Sonicwall 2040 as their sole connection. They are utilizing an address scheme of 10.0.0.x. My network uses a 192.168.x.x network and BGP/IPFR to network all of the r...

I have some remote offices that are going to have a 2nd T1 line installed which will be used strictly for video conferencing. I know that the 2800 series will support video but will the older 1700 series routers support high speed video conferencing...

Resolved! 2811 specification

Hello All,Does anyone know if I can use the Cisco 2811 router as a layer 2 switch only? I need to replace Alcatel OmniAccess 512's in a network (these are LAN/WAN switches - 12 x 10/100 tx LAN ports and frame-relay over 2 x E1/T1 WAN ports ).I was th...

Dear Sir,I have two IOs images in disk2 of 7206VXR . I want to boot the router with second image which is stored in disk2 . I have already tried boot system flash disk2: IOS.bin command & bootldr but is not working Help on same Aman

amansoi_5 by Level 1
  • 1009 Views
  • 8 replies
  • 0 Helpful votes

Hi,As annouce the cisco 1750 router already EOL. Does the new Cisco 4 ports Fast Ethernet Switch WIC and Single Port Ethernet WAN Interface Card compatible with Cisco 1750 router?Can it be integrate into that router?thanks

Good mooring,Please,i need a simple configuration example with vrf between 2 routers acts as PE and P.Regards.