1.In the Below diagram if PC-A starts sending packet where would the fragmentation start ? How many times will the packet be fragmented , will it be only once or more than once , if so how ?
1.In the Below diagram if PC-A starts sending packet where would the fragmentation start ? How many times will the packet be fragmented , will it be only once or more than once , if so how ?
My company wants to implement bgp on a single router for dual ISP redundancy for a branch warehouse, we don’t have BGP with the ISP we have a 1G internet line from provider 1 and 500Mpbs from provider 2.Now Do I need to call my isp to have BGP so the...
I have two homes on the same building flour. Earlier ISP administration allowed me to use single connection in both homes. So ISP connection was provided to one home and then I had a router configured as AP at another home. The AP-router is connected...
Team; I am unable to pingFrom Router 2 I cannot ping 3.3.3.4From Router 3 I cannot ping 4.4.4.4From Router 3 I cannot ping 2.2.2.3From Router 4 I cannot ping 3.3.3.3I have attached the configuration please help.
Team please help this Noon;I am unable to pingFrom Router 2 I cannot ping 3.3.3.4From Router 3 I cannot ping 4.4.4.4From Router 3 I cannot ping 2.2.2.3From Router 4 I cannot ping 3.3.3.3I have attached the configuration I did and below are the IP rou...
Hi,I have a LAN with a very basic setup (one switch and one router) with no local DNS server (I use 8.8.8.8 as server).I recently started hosting a website so I have 2 NAT rules: 1. A NAT overload rule allowing my local PCs to access the Internet2. A...
Hi,Is there any solution (except using PBR) for controlling the outgoing traffic to the service providers from our side?We want each buildings send/receive traffic go through each provider, while all providers can act as backup for others. For contro...
Hi,I have a router and NVRam seems to be damaged or corrupted Cisco 2921. Can we change the NVRAM ram physically? because i changed the cf card and still doing the same. Router#wrBuilding configuration...[OK]Router#*Sep 14 15:11:35.471: %NVRAM-2-NO_G...
Is there a doc covering the IPSEC performance of the ISR 829 Industrial Router Series?
Hello,My manager wants me to find an answer to this topic. We have a class C public subnet that is ours, and we have two data centers with ISR routers with full BGP neighborship to two different ISP at each data center. Those BGP routers are also nei...
Hi all guys,I have a simple static NAT config.TopoClient (f0/1) ----192.168.0.0/24----(f0/1)R1(f0/0)----200.0.0.0/24----(f0/0)R2IP addressesIP Client:f0/1: 192.168.0.10/24IP R1:f0/1: 192.168.0.1/24f0/0: 200.0.0.1/24IP R2:f0/0: 200.0.0.10/24 ConfigCli...
After configuring my 2 SG220 switches I'm getting the following error when I give the show run command: SIGSEGV# *Jan 01 2000 03:26:06: %System-4: System rebootThis reboots the switch. This happened to both my switches near simultaneously. I can't fi...
help me to clarify layer 2 switch can support dual ring topology..
Hi everyone, I have a general question about some communication failure because of BSTUN protocol. Actually it is not certain but my opinion. Issue is when I configure BSTUN protocol, this config running for a while but after communication drop. I ...
Hello everyone,I have a question about the configuration of RADIUS on a Cisco 1941 router.I am using Microsoft Policy Server as a RADIUS server for my router and I got it working but only when using the unencrypted protocol PAP. I wish to use the mor...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-28-2024 04:59 PM | ||
07-15-2024 05:07 AM | ||
07-13-2024 09:04 AM | ||
07-09-2024 05:41 AM | ||
07-03-2024 08:54 PM |
User | Count |
---|---|
12 | |
8 | |
6 | |
5 | |
5 |