Routing

I am new to the 877 routers and I am having a really hard time getting an IP address from SBC ("Sticky IP"). I have tried changing the DSL operating-mode but to no avail. I have uploaded a copy of my current config, as I have it set up. I can bring m...

Hi, there. I'm daniel Seo.Our client is Cable TV company. So They serve multicast services to downstream SO companies. I want you to see the attached file(Network diagram). They said "We're seeing the unserviced multicast ip address at the console of...

Is it tecnically possible to connect a router with T3 port to a router with E3 port?Can you give me a detailed explanation of why yes or no?Thanks a lot!

Is it tecnically possible to connect a router with T3 port to a router with E3 port?Can you give me a detailed explanation of why yes or no?Thanks a lot!

Hi,It's seems that the Version 2 of the DSU/T1 wic is not working on Cisco 2621 classic. I tried with 3 different IOS, 2 routers and 2 WIC-V2.I always got the unrecognized WIC error messages. The Cisco documentation stipulates that IOS 12.2(15)ZL is ...

I have got a virtual-access interface on a router. i don't know from where it came in. There is no PPP multilink on this router.Can someone please explain this?Attached is show run and show ip int brief.Thanks

I'm trying to turn on logging on our Cisco 837 ADSL routers to populate my syslog server. I have set these up as LAN-to-LAN's which connect to our Cisco 3000 concentrator. I have added the code below to the routers config, but the only time my syslog...

Hi,Please review my attached .jpg for a more detailed explanation.I am trying to set up GLBP to load balance 2 routers, 1 serial link (GLBP weight 100) and 1 isdn link( GLBP weight 90) connected to the same router via differnent mediums.I am using os...

I just want to know in general, does a telecommunications switch can handle different layer 2 wan technologies (Frame Relay, ATM, ISDN--etc)? or it should be specified for specific technology only ? Yes I know there are different modules and type of ...

HiI need to configure a router for my company. we require 3 fast ethernet port with one serial link .So, please suggest me that if this configuration is rightCisco 2801 2801 w/AC PWR,2FE,4slots(2HWIC),2PVDM,2AIM,IP BASE,64F/128DWIC-1T= 1-Port Serial...

Hello, team!I have cat6500 (sup-720) and I want configure gre tunnel within VRF. I used next configuration:ip vrf test rd 100:100interface Tunnel0 ip vrf forwarding test ip address 172.31.254.253255.255.255.252 keepalive 5 3 tunnel source 10.112.86.6...

Hi all,I'm looking for a PA that can offer more than 8 Mb over one serial port (i'm using a 449MT cable).I know that with a PA-4T you agregate 4 X 2 Mb over one single serial port but I've to go uo to 16 Mb.I'm not interested by the PA-H (HHSI).thks ...

what does KLM means?...does PA-MC-STM-1SMI card has KLM configuration?...actually i have 7606 router and it has PA-MC-STM-1SMIand i have configured this STM-1 on E1 unframed , and had given loopback network for testing.now the engineer at the far end...

6509 s/w catos upgrade question --------------------------------We have 3 x 6509 switches, each with Sup2 and MSFSC2 cards. These 6509's are running in hybrid mode (i.e. IOS for MSFC2 and Catos for Supervisor II card and IOS revision 12.1(13) on the ...

Hello,Recently I install a PA-GE on a cisco 7206 with a NPE 400 and get this message:%FX1000-3-NOTFX1000: PA bay 2, device number 0: unknown device (0xFFFFFFFF)%PA-3-DEACTIVATED: port adapter in bay [2] powered off.the ios that is running on cisco is...