Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Webinar

 
Labels

Forum Posts

In my area, I want to take 1 MB link for my head office. Service Provider is giving it in both flavors, Frame-Relay and ATM.I am confused that which service I should avail. Frame-Relay is definitely cheaper than ATM. But what benefits ATM 1 MB link w...

Hi allI have 2 depts distance is around 500 mts, rt now we are using "Pairgain" over 2 pair copper( 4 wire, ordinary telephone cable)its actually HDSL.but now a days pairgain is not available so i'm planning to replace all these pairgain systems usin...

Hi everyone...I have cisco router with two ATM interfaces and one LAN interface. I have a user who want to access two applications at the same time, each application lies on a different ATM port. So, is it possible.Also, i want to do NAT for my user...

kareem911 by Level 1
  • 488 Views
  • 1 replies
  • 0 Helpful votes

Hi Experts,Need your suggestion on an interface bandwidth part which is confusing me a lot.How do we measure the interface bandwidth i.e if I have an interface 2MB E1, when I see the link utilization in my monitoring tool (live ) its shows in that in...

I have configured VTY lines on L3 switch like this --line vty 0 3line vty 5 14line vty 15When I am giving any of the command like -no line vty 15ORno line vty 5it results ----% Can't delete last 16 VTY linesI want only line vty 0 4 on this L3 2850 sw...

rupaheli by Level 1
  • 16743 Views
  • 7 replies
  • 0 Helpful votes

I have lease line 2 Mbps terminated on my serial interface with ip unnumbered command my fast ethernet has real valid ip which is being used by serial interface and this fast ethernet is connected to pix firewall and once in a day my data tx stops ...

Is the return traffic taking the same route path as it has traversed? Or the destination end router will change the path if there is a specific route entry in routing table that directs the packet to another path. Both end are using cisco router with...

kennylls by Level 1
  • 4678 Views
  • 7 replies
  • 0 Helpful votes

Hi, I've read that the 1720 router support connections up to 2048 Mbps. Is this the limitation of the router or the interface? I mean, can I have 2 serial interfaces both 2048 totalizing 4096 Mbps?Thanks

muca by Level 3
  • 348 Views
  • 1 replies
  • 0 Helpful votes

Hi Experts,I Have implemented and worked on HSRP/VRRP and now just trying to get the GLBP. Before I configured that I have some doubts that I would like to get cleared :I read the GLBP Docs and here are the points :1. What is the main diff between th...

Hello,Since two months we have problems on a DS3 line between France and UK.From time to time we see many carrier transitions on WAN interfaces even if they don’t go down.Our SP sees everything is OK on the link.We have changed the PA adapter on both...

flaxague by Level 1
  • 729 Views
  • 2 replies
  • 0 Helpful votes

Hi All,Im having issues with one of our T1's.Im seeing the reliability going up and down on the interface due to which there are too many carrier transitions and lot of input and crc errors are being generated.The other end router shows up clean.I ha...

I recently setup Cisco VPN access for some of our remote users. While the users are VPN in they are not able to access resources using the UNC name. The ip address works just not the UNC name. I think it is something in my ACL. Can someone offer any ...

can RIP perform load balancing?. i am going to have fibre link and a frame-link connected to a 3600 series router.they are currently using RIP. this site is central site and 16 remote sites connect back to it. do i have to use OSPF or igrp?

a.gooding by Level 5
  • 383 Views
  • 3 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card