Hello, Here's a my topology: As you can see, R1, R2, R3 and R4 are configured with OSPF (all the networks connected are declared). My goal is to configure R5 only with sating routing to better understand how it works.So I configured all the static ro...
HiWe recently have the following log on our ASR903: %CMRP-3-SOFT_ERROR_RELOAD_RECOMMENDED: R0/0: cmand: Uncorrected Soft error on ARAD_1, reload is recommended to recover.%CMRP-3-SOFT_ERROR_UPDATE: R0/0: cmand: Soft error on ARAD_1%CMRP-3-SOFT_ERROR_...
I have two RV340 routers setup at various locations, and are working properly with this exception. When I initiate a client-to-site vpn, I can only access approximately 10 ip addresses on the internal network. I haven't found anywhere in the config...
1. How can I tell if this router supports Fiber or copper 10G SFP? Since it says SFP Ethernet - Does this mean it only supports ethernet cables(copper) not Fiber optics? Or supports both?2. It says SFP not SFP+. From what I read only SFP+ support 10...
Hello everbody,I bought an RV160 just to make a nat translation form one router to an networkTopology = Cisco877>>>CiscoRV160>>>>customer networkI am having this problem, I would like to NAT an adress 172.16.244.22 on my wan port to a 192.168.253.10...
Hello, Here's a simple topology: I'd like to know which protocol or configuration I have to use to create my backup link considering that my routers are using OSPF. I only find solutions that use HSRP with two routers. Thanks.
Hi i have some clients site where all will be connected to one switch and connect to main site with firepower which managed with FMC whats the best design in this scenario my thoughts will be using /30 subnet from client side to firepower middle swi...
Hallo. I have the following network. I have already set the red router, sothat i can reach the google-server from all of my network(DMZ, LAN & Public). Now i am trying to simulate a backup ISP(the green router). The aim is to be able to ping bthe goo...
I have the following subnets below. i want to let traffics from the green subnet to go everywhere but the blue subnet(DMZ) should not be able to get into the green Network. How do i prevent the blue network get into the green network ? what should i...
Hello Expert, I humbly request some guidance for the caption cannot find a security option in the GUI,and unable to open a telnet or SSH. Please provide some guidance Regards
Does anyone know the explanation for the logs that appear on the ASR920 and ME3600? Logs below. Jun 10 18:27:08.771: %SYS-2-MALLOCFAIL: Memory allocation of 24835080 bytes failed from 0x48FF85C, alignment 0Pool: Processor Free: 352781344 Cause: Memor...
Good morning all,I have a quick question about the blackhole. Currently my forwarder told me that his BGP community for a blackhole prefix (/ 32) was 65535: 666.I have configured the options in my router and indeed, if I blackhole a prefix, it is no ...
I am running CML version 2.2.1 and have been experience lots of problems:1. Connection labels are not correct quite a few times. For example, I connect port G0/1 on a router to port G0/1 on a switch and the connection shows router G0/1 - switch G0/...
Good day board - Can one use a loopback to activate area 0? I have a setup where I desire a star topology and would prefer a loopback over other options. The state and configuration are:sh ospf ... Area BACKBONE(0) (Inactive) Number of interf...
I have recently updated a firmware on a cisco 4300, after the *reload* cmd I gave, it is looping the boot. How do I stop the boot and maintain the given update?I should mention I also did the confreg 0x2142 then reset. I know its a novice question.
