Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

Hello,question about BGP IGP tag:On Cisco when i'm doing [aggregate-address summary-only] command the summary route is created by BGP is with IGP tag. Even when no of suppressed routes has an IGP flag.  But the RFC says:ORIGIN attribute: If at least ...

from88 by Level 4
  • 1047 Views
  • 4 replies
  • 0 Helpful votes

Hi.Expieriencing some increasing timeouts on ip virtual-reassembly  GigabitEthernet0/0/2.202: Virtual Fragment Reassembly (VFR) is ENABLED [in] Concurrent reassemblies (max-reassemblies): 16 Fragments per reassembly (max-fragments): 32 Reassembly tim...

vudex by Level 1
  • 1992 Views
  • 2 replies
  • 0 Helpful votes

Hi all,  I have a configuration with default route injection on NSSA area:  area 31 nssa default-information-originate no-summary This announce seems is always active. It is not related to default route presence on route table. So seems that "always"...

Map23 by Level 1
  • 1358 Views
  • 4 replies
  • 0 Helpful votes

Hi,I would need some help with a NAT problem.With some previous help from this community I configured a Cisco ISR 1113-8p, but I cannot allow users from outside my LAN to access to some hosts inside my LAN. They're getting a "connection refused". mes...

broberto82 by Level 1
  • 4469 Views
  • 17 replies
  • 0 Helpful votes

need to know whats the network id and the summerization is for the below sub interfaces please: connected to isp  192.168.1.0/24 this is should be private subnet or not becuase this is conected directly to wan isp routerFACE-client2192.168.2.0/24Prin...

i have 1 isp 2911 router ------- sw(witches connected to my isr 2911 router take the time from ntp server )------sw(witches connected to my isr 2911 router take the time from ntp server ) regarding the syslog configuration as below should i applying ...

Hello, I'm new here, I want to execute GDOI command on Cisco 1700 router in GNS3 but it doesn't execute and says "invalid input "  what's the problem ?? the command is " crypto gdoi group GDOI_GROUP " the error is    " invalid input detected at '^' m...

Ahmed90 by Level 1
  • 2860 Views
  • 6 replies
  • 0 Helpful votes

Resolved! ASA 5508-X & VLan

Good Morning I was curious about the VLAN situation on my 5508. Each Interface (aside from GE1 (WAN) and GE2 (Admin/ASDM) is set up with it's own IP Address such as 192.168.3.1, 192.168.4.1, and so on. When I run the command "show vlan" it comes back...

fbeye by Level 4
  • 1802 Views
  • 2 replies
  • 0 Helpful votes

My ISP gave me PUBLIC WAN IP and PUBLIC LAN IPs. Can someone help me with fresh configuration of the Router. WAN IP: 136.xxx.xxx.x6SUBNET: 255.255.255.248GATEWAY: 136.xxx.xxx.x5 PUBLIC LAN IP POOL: 115.xxx.xxx.110115.xxx.xxx.111115.xxx.xxx.112115.xxx...

Sanga62 by Level 1
  • 956 Views
  • 3 replies
  • 0 Helpful votes

I have a newly installed Cisco 4431 that is exhibiting some odd behavior. From the router itself, I can ping 8.8.8.8 and from the router webpage, I am able to "Test WAN Connection" to 8.8.8.8 and get all green.From clients behind the router, from com...